Bedienungsanleitung Felisatti AF180 (Seite 6 von 45) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch)

502483

Zoom out

Zoom in

Vorherige Seite

1/45

Nächste Seite

2. To return to the initial position, do the same in re-verse.

ACCESSORIES

Accessories and their corresponding order number can be

found in our catalogues.

MAINTENANCE AND CARE

CAUTION! Always unplug the machine before carrying out

work on it.

- Inspect the tool: Using a worn deburring or cutting tool

will diminish the efciency of the work and could damage the

motor.

- Inspect the mounting screws: Regularly inspect all the

mounting screws and ensure they are rmly tight-ened.

Should any screw be loose, tighten it immedi-ately. Failure to

do so could put you at serious risk.

- Motor maintenance: Always take the greatest care over

this and make sure that the motor winding is not damaged

and does not become wet with oil or water.

- Brush replacement: The brushes disconnect auto-

matically and should be replaced after 150 - 200 hours use

or when they are less than 10 mm long. Have this done by an

Ofcial Service Centre.

- The vents should always be kept clean and free of

obstacles.

- Clean the machine thoroughly after each use. Blast the

motor regularly with compressed air.

- Check that the mains lead is in good condition. If it is not,

take it to an Ofcial Service Centre to have it re-placed.

- Use only Felisatti accessories and spares. Parts the

changing of which is not covered in this instruction manual,

should be replaced in a Felisatti Ofcial Service Centre (See

Warranty/Ofcial Service Centre address leaet).

WARRANTY

See general warranty conditions printed on the attached

sheet.

WARNING! Never press the blocking button C when the

machine is running. The shaft must have stopped com-

pletely before the blocking button C is pressed.

To t the disc, proceed as follows:

1. Block the spindle (shaft) J by pressing the blocking

button C.

2. With the pin spanner G remove the clamping nut H from

the spindle J.

3. Fit the abrasive disc on the support plate I.

4. Replace the clamping nut H using the pin spanner G

The position of the nut H will depend on the thick-ness of the

disc (see g. 4 and 5).

5. Once the disc is tted, check that the blocking button

has returned to its original position due to movement of the

incorporated spring.

STARTING THE TOOL

CAUTION! Check that the mains voltage is the same as that

in the machine’s specications.

Plug the machine in with the switch off.

This model has a safety switch to prevent the machine from

starting up unexpectedly.

Starting the machine: Press the button A and pull the trigger

B simultaneously, until the latter starts to operate. The trigger

switch B will block for continuous operation.

Stopping the machine: Pull the trigger switch B.

Start-up current reducer

The machine’s start-up current exceeds the rated cur-rent.

By means of this reducer, the current is reduced to the point

where the fuses (slow 16A) do not blow.

WORKING INSTRUCTIONS

For cutting or deburring, the part to be worked on must be

secured, unless it is heavy enough to remain in a stable

position by itself.

For optimum performance and results when deburring,

it is advisable that the surface and the disc form an angle

of approximately 30º-40º. Guide the tool by pressing

lightly forwards and backwards. This prevents the part

from overheating or changing colour and the formation of

striations.

CAUTION! Never use a cutting disc for deburring.

When cutting, do not exert pressure on the disc. Do not tilt

the machine. The disc should not tilt or oscillate. Work with

a steady speed, appropriate for the type of material. When

cutting, bear in mind the direction of the work. Guide the

machine against the direction of the cutting tool, never in the

opposite direction; otherwise there is a risk of the machine

veering off the cutting line uncontrollably. When cutting

proles or rectangular section tubes, we recommend starting

the cut on the shortest side.

ADAPTING THE REAR HANDLE

CAUTION! For safety reasons, the machine should always

be unplugged from the mains before changing the disc or

wheel.

The rear handle L may be turned 90º to the left and to the

right in relation to the motor housing.

This enables the ON/OFF switch to be turned to the most

suitable working position; for example, for cutting with a guide

stand (accessory) or for the left-handed.

To turn the rear handle, follow the instructions below:

1. Press the rear handle turning button K and, at the same

time, turn the rear handle L to the left or right until it locks.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Felisatti AF180 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info