Bedienungsanleitung Felisatti MTF250 (Seite 5 von 16) (Deutsch, Englisch, Spanisch)

502514

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

which is raised by the work when it comes close to the cut.

WARNING – these protectors must not be removed, in order

to prevent danger for the operator.

• In the event that the switch lock button has not been

engaged, the machine will stop automatically when the

handgrip is released.

WARNING –engaging thelock buttondisables thesafety

device provided by the manufacturer and enables push-

buttonstart.Itisrecommendedthatthisdevicebeusedwith

theutmostcaution.

The tool has been designed and built so that it is possible to

work in all situations with total safety, however, in special working

conditions, gloves and protective goggles should be worn.

The tool has been designed and built to reduce noise to a

minimum (see technical data), however, in special conditions the

maximum noise level in the workplace might exceed 85 dB(A).

In this case, the operator should protect himself from excessive

noise by using ear protectors.

GENERAL SAFETY REGULATIONS

See manual “Safetyinstructions” which is supplied together

with this instructions manual.

INSTALLATION

1. ELECTRICAL CONNECTION

Before connecting the machine to the mains, one must make sure

that it complies with current regula-tions in the country where it is

used and that the voltage and frequency are as indicated on the

char-acteristics plate.

When extensions are used, make sure that the cross section of

the cables is suited to their length. If using roll up extensions,

make sure that they unroll completely in order to prevent

overheating.

WARNING–beforeplugginginthemachine,makesurethat

theswitchlockbuttonisreleased.

2. WORKPLACE

The tool that you have purchased is a transportable or semi-

stationary electric tool. Only one operator is needed to use it,

given its structure, weight and ease of handling.

In normal use, the operator is in front of the machine with the

handle to his right. The right hand on the handle allows the

machine to be handled completely, in fact, the switch and a safety

hook may be accessed without releasing the handle.

CONSTANT ELECTRONICS

The built-in module permits:

- Soft start.

- The maintenance of a practically constant rated speed up to

rated power.

- An overload protection system by means of current cut-off

in the case of motor overload, in which case the burring machine

shuts down and re-starts when the grinding pressure has been

reduced.

MITRESAWADJUSTMENT-SQUARING

The mitre is delivered by the manufacturer already adjusted and

squared according to standard pa-rameters.

WARNING – before making any adjustment of the mitre,

unplugthemachine.

1. BLADE UNIT LIFTING

An internal spring keeps the motor unit at rest position (raised).

In this position, a safety hook prevents the unit from being

activated accidentally.

1.1 To unlock the motor unit and to be able to use the machine as

a mitre saw, activate the front button D (Fig.1) (the operation may

be carried out with the right hand on the handle).

1.2. To use the machine as a bench circular saw, unlock the

motor unit as indicated in 1.1, and after lowering it completely,

block it with pin P (Fig.1a).

2. BLADE PENETRATION ADJUSTMENT

The depth of penetration has already been adjusted by the

manufacturer during testing.

As incorrect adjustment may cause sharpness to be lost quickly

and/or the teeth of the blade to be broken, further adjustment

might be needed, in which case it will be necessary to work as

follows:

- Activate bolt A (Fig.1а) and the corresponding lock nut to

create a lower limit for the motor housing ideal for preventing

the blades from coming into contact with the turntable.

WARNING–onceforthisoperationiscomplete,makesure

thatthebladeisNOTincontactwiththeturntableandthat

thelocknutistightened.

3. TURNTABLE ADJUSTMENT

0ºRegulation(Fig.3)

- Lower the head of the machine and lock with pin P (Fig.1a).

- Set the turntable to zero.

- Loosen the handles V, remove the guides X – Optional

accessory and loosen bolts Y.

- Set a square between the saw blade and guide M (Fig.1).

- Keeping the turntable at zero, move the guide to 90º on the

square.

- Tighten bolts Y, assemble guides X and adjust handles V –

optional accessory.

4. ADJUSTING THE SAW BLADE WITH RESPECT TO THE

WORKING PLANE

90ºadjustment(Fig.2)

- Lower the head of the machine and lock with pin P (Fig.1a)

- Place a square between the base and the saw blade.

- Loosen lever O and adjust with bolt Z.

- Tighten the lock nut well to make sure that the position is

xed and tighten lever O.

5. VERTICAL PLANE LIMIT STOP ADJUSTMENT (0º - 45º)

(Fig.2)

- Lower the head of the machine and lock it with pin P

(Fig.1a).

- Set the turntable to zero and lock.

- Set the head to 45º and lean a 45º square between the base

and the saw blade.

- Loosen lever O and adjust using bolt Z.

- Regulate the 45º using bolt Z1 (Fig.1a), after releasing the

lock nut.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Felisatti MTF250 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info