Bedienungsanleitung Ferm fos-180 (Seite 4 von 22) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch)

389403

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

4 Ferm

Interruption of the mains plug, mains lead or •

mains lead damage.

Defect switch•

Smoke or stench of scorched isolation•

Electrical safety

When using electric machines always observe the

safety regulations applicable in your country to

reduce the risk of fire, electric shock and personal

injury. Read the following safety instructions and

also the enclosed safety instructions.

Always check that the power supply

corresponds to the voltage on the rating

plate.

Class II machine – Double insulation –

You don’t need any earthed plug.

Replacing cables or plugs

Immediately throw away old cables or plugs

when they have been replaced by new ones. It is

dangerous to insert the plug of a loose cable in the

wall outlet.

Using extension cables

Only use an approved extension cable suitable

for the power input of the machine. The minimum

conductor size is 1,5 mm

. When using a cable

reel always unwind the reel completely.

3. ASSEMBLY

Prior to mounting an accessory always

unplug the tool.

Dust collection

Fig. 2

The sander has been carried out with a dust bag

(3) to keep the working surface clean. The dust

bag must be installed on the back side of the

machine, on the opening. It is necessary to empty

the dust bag regularly for an efficient use.

Empty it as follows:

Turn the dust bag slightly and pull it out of the •

machine’s adapter.

Empty the dust bag in a suitable place.•

Push the dust bag on to the machine’s adapter •

till it locks into place.

Remember that the dust extraction only

works when using perforated

sandpaper.

Replacing worn sanding paper

Fig. 3

Before assembly sanding paper always

remove the plug from the mains.

Replacing worn sanding paper

This machine is suitable for Velco

sanding paper

and universal sanding paper.

Before assembly sanding paper always

remove the plug from the mains.

Velcro

sanding paper (189 x 92 mm)

The sandpaper is fixed by Velcro

fastener to

facilitate the replacement.

Simply pull off the sanding paper.•

Press the new one in the centre of the sanding •

sole.

Universal sanding paper (240 x 92 mm)

Fig. 3

The sanding machine is provided with a rectangle

sanding sole. By tightening the sandpaper it does

not wear out so fast, so it will wear well longer.

Open the back paper clamp (4) by pulling the •

handle (5) up.

Install the sandpaper under the clamp. Put the •

paper in the middle of the sanding sole and

look after the perforations in the paper. They

have to correspond with those on the sanding

sole, so that the dust can be exhausted.

Push the handle back into its original position.•

Repeat the operation to fix the sand-paper on •

the front side.

Fix the sandpaper as tight as possible.•

Coarse sand-paper (grain 50) removes in general

the bigger part of the material and fine sand-paper

(grain 120) is used for the finishing.

Replacing the sanding sole

The sole has to be replaced when the Velcro has

been worn out.

41Ferm

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm fos-180 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info