Bedienungsanleitung Ferm PMM1006 (Seite 4 von 92) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

510103

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

4 Ferm

Wear eye protection



• The tool should not be operated in damp, wet

premises; during a rain, fog and snow in the

open, and in environment with a risk of

explosion.

• The switch should be in “OFF” position before

putting the plug in the mains socket.

• For long hair, wear hair protection. Work only

with closely fitting clothes.

• Secure the vessel with the mixed substance

against moving on the floor.

• Always direct backwards the flexible lead from

the tool. The flexible lead should not be

exerted by tensile stress and should not lie on

or pass over sharp edges.

• Use the supplementary handle.

• Consider possible reaction torque.

• Wear ear and eye protection.



• Excessive sparking of the carbon brushes and

verticiliosis in the collector.

• Interruption of the mains plug, mains lead or

mains lead damage.

• Defect switch

• Smoke or stench of scorched isolation



When using electric machines always observe the

safety regulations applicable in your country to

reduce the risk of fire, electric shock and personal

injury. Read the following safety instructions and

also the enclosed safety instructions.

Always check that the power supply

corresponds to the voltage on the rating

plate.

Class ll machine. Your machine is double

insulated; therefore no earthwire is

required.

Replacing cables or plugs

Immediately throw away old cables or plugs

when they have been replaced by new ones. It is

dangerous to insert the plug of a loose cable in the

wall outlet.

Using extension cables

Only use an approved extension cable suitable

for the power input of the machine. The minimum

conductor size is 1,5 mm

. When using a cable

reel always unwind the reel completely.



Placing a whisk

Remove the plug from the mains before

placing a whisk.

Use only whisks conform the specified diameter.

• Screw the whisk with tread (M14) as far as

possible in the tool

• Tighten the whisk properly with an open-end

wrench

4. Use

Improper use may damage the instrument.

Observe therefore these instructions:

• Use a tool up to the specified diameter.

• Load the tool in such a way that the speed

would not drop considerably or that it would

stop.

Check if the data on the rating plate correspond

with the actual mains vol tage.

Instrument scheduled for 230 V can be plugged to

220 V/240 V mains.

The ON/OFF switch

• To switch on the tool, press and hold the on/off

switch (1).

• If you release the on/off switch, the tool will be

switched off.

Switch locking mechanism

You can lock the on/off switch by pressing the

on/off switch (1) and then button (2). The switch

lock can be released by briefly pressing the on/off

switch.



Starting current limiting

The electronically controlled smooth start takes

care that the machine starts without jerk. In this

manner, the splashing of thin liquid materials is

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm PMM1006 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info