Bedienungsanleitung Ferm PMM1006 (Seite 5 von 92) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

510103

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

Ferm

prevent at the same time when switching on the

machine.

As a result of the machine’s reduced starting

current, a 16 A fuse is sufficient.

No load speed reduction

The electronic control reduces the no-load speed

of the machine which results in reduced noise and

wear of motor and gear.

Speed pre-selection

With the speed control (3) the speed can be

continuously pre-selected: the necessary speed is

dependent on the type of material to be mixed. It is

recommended that it be confirmed with a practical

trial.

Speed selection

Two rpm ranges can be pre-selected with the

speed selector switch (4):

Gear 1 180-380 r/min

Gear 2 300-650 r/min

The necessary speed depends on the type of the

material mixed and it is recommended to verify it

by a practical test.

Constant electronics

The constant electronics keeps the speed

between no-load and load nearly constant and

ensures uniform mixing of the materials.

Electronic overload protection

In case that the machine is extremely overloaded,

an electronic overload protection protects the

motor from damage. In this case, the motor stops

and restarts only after the feeding pressure is

reduced.

Temperature-dependant overload protection

To protect the motor from overheating at extreme

permanent load, it is switched off by the protective

electronic system when a critical temperature is

reached.

After a cooling-down period of approx. 3-5 min.,

de machine is again ready for use and can be fully

loaded.

When the machine is warmed by use, the

temperature-dependent overload protection reacts

earlier as a result.

6. Service & maintenance

Make sure that the machine is not live

when carrying out maintenance work on

the motor.

This machine has been designed to operate

over a long period of time with a minimum of

maintenance. Continuous satisfactory operation

depends upon proper machine care and regular

cleaning.

• The ventilating slots on the motor casing

should be cleaned out from time to time.

• After 100 hours: check carbon brushes

• After 200 hours: renew the grease filling in the

gearbox

Cleaning

Regularly clean the device’s casing with a soft

cloth, preferably after each use. Keep the fan slits

free of dust and dirt. Remove stubborn dirt using a

soft cloth, dampened with soapy water. Do not use

solvents such as benzene, alcohol, ammonia, etc,

which might damage the plastic parts.

Lubrication

The device does not need any additional

lubrication.

Defects

If a defect appears due to a part wearing out,

please contact the service center on the warranty

card. Separately you will find an exploded view

showing the parts that can be ordered.

Environment

To prevent damage during transport, the appliance

is delivered in a solid packaging which consists

largely of reusable material. Therefore please

make use of options for recycling the packaging.

Damaged and/or disposed of electrical or

electronic devices must be dropped off at

recycling stations intended for that

purpose.



Read the warranty conditions on the separately

supplied warranty card.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm PMM1006 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info