Bedienungsanleitung Futaba FP5NLH (Seite 6 von 6) (Englisch)

30012

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

This horn permits shifting of the

servo neutral position at the servo

horn. Setting and shifting the

neutral position

a) Angle divisions

Fig.

1) The splined horn has 25 seg-

ments. The amount of change per

segment is; 360 /25=14.4°

2) The minimum adjustable angle

is determined by the number of

arms or number of the holes. For

four arms, the minimum adjustable

angle is:

b) Effect

Fig.

To shift the holes center line to

the right (clockwise) relative to

baseline A, shift arm 2 to the po-

sition of arm 1 and set it to the

position closest to baseline A.

[Example] For a four arm horn,

the angular shift per segment is

14.4°. The shift to the right is 90°

- (14.4 x6) =3.6°

To shift by the same angle in the

opposite direction, use the oppo-

site arm number.

Fig.

Arm 3 shift 4.8° to the right, arm

6 shifts 2.4° to the left,and arm 4

shifts 7.2° to the right and left.

For a six arm horn, turn the arm

counterclockwise and set arm 2

to the position of arm 1. The ad-

justable angle is 60° — (14.4 x 4)

=2.4°.

Fig.

The following splined horns are optional.

Fig.

Baseline A

HORN A HORN B HORN C HORN D HORN E HORN F

Fig.

No.

10.

11.

12.

13.

14.

15.

16.

17.

18.

19.

20.

21:

22.

23.

24.

Part Name

Upper case

Middle case

Bottom case

Ball bearing

Potentiometer

VR drive plate

Motor

Motor pinion

1st gear

2nd gear

3rd gear

Final-gear

2nd shaft

Intermediate shaft

Spacer washer 0.3T

Seal ring

0-ring

Servo horn D

Horn mouting screw

S130 printed wiring board

Lead wire packing

S1303PB WRB.300

Screw 0-ring

Case mounting screw

S130 Nameplale

Part No.

FCS-30

S04130

139995

S02753

S91243

S02461

FGS-30

S02481

S02480

S02486

S90415

S90426

FSH-6W

FSH-41

AS1220

S90045

FPC.8M

S90410

J50085

S6010)

To insure prompt service, please follow the instructions given below.

Charge the

batteries

for

least

18 hours

prior

shipment.

Return

the

system

only.

Not

your complete

inital'alion.

Remove the

servos

from their

mounts and remove the foam padding from the receiver.

3. Plugs or other modifications which interfere with factory test procedures will be returned to

factory standard at your expense.

4. Carefully pack all components individually, using sufficient packing material to prevent

damage during shipment.

5. Include a brief but thorough explanation of all problems and service required and tape it to

the back of the transmitter. Place a label describing the function of the servo on each servo-

6. Be sure to include your full address and tel No.. zip code inside the box as well as on the

outside.

7. Include a packing list of all items being returned, and double check to make sure that all

items are packed.

8. Upon receipt of your equipment at the Futaba factory, an estimate of the cost of repair

(over $25 00 only) will be sent to you. Your equipment will then be repaired and returned

to you upon receipt of payment or C 0 D (cash)

This factory repair service applies only to the continental U.S.A., Hawaii, and Alaska.

The flag can be attached to

and removed from the end

of the antenna with one touch.

Staple or glue with

cyanoacrylate

ribbon here.

First

digit

Second

digit

Insert the frequency flag into

the flag holder as shown here.

Fig.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba FP5NLH Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info