Bedienungsanleitung Garmin 9 axis Heading Sensor (Seite 2 von 4) (Englisch)

691897

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

• Do not use excessive force when installing mounting screws.

Use only the amount of force needed to keep the sensor in

place.

• Apply force evenly between the mounting screws.

NMEA 2000 Connection Considerations

• This sensor connects to an existing NMEA 2000 network on

your boat.

• If the included NMEA 2000 drop cable is not long enough to

reach your NMEA 2000 network, a drop cable of up to 6 m

(20 ft.) can be used, according to the NMEA 2000 guidelines.

Item Description

Sensor

NMEA 2000 power cable (existing; not included)

Ignition or in-line switch (existing; not included)

12 Vdc power source

NMEA 2000 T-connector (included)

NMEA 2000 terminator or backbone cable (existing; not included)

Calibration

After installation is complete, you must calibrate the heading

sensor for best results. Depending on the types of devices

connected to the NMEA 2000 network, you can calibrate the

sensor using either a menu-based method or a basic method.

When you connect the sensor to the same NMEA 2000 network

as a compatible Garmin chartplotter, you are prompted to begin

menu-based calibration when the chartplotter detects the new

sensor (Performing Menu-Based Calibration, page 2). Go to

www.garmin.com for a list of compatible chartplotters.

NOTE: A software update available in mid-2017 enables you to

perform menu-based calibration using a compatible chartplotter.

If your chartplotter has software that predates this update, you

must perform basic calibration.

If you connect the sensor to a NMEA 2000 network without a

compatible Garmin chartplotter, you must perform basic

calibration instead of menu-based calibration (Performing Basic

Calibration, page 2).

Performing Menu-Based Calibration

Before you can perform menu-based calibration, you must

connect the sensor to the same NMEA 2000 network as a

compatible Garmin chartplotter.

If the sensor has not been calibrated successfully, a message

appears each time you turn on a compatible Garmin chartplotter.

From the sensor calibration screen, select Compass Cal..

TIP: You can open the calibration page at any time by

selecting the device from Menu > Settings >

Communications > NMEA 2000 Devices.

Select Begin.

Follow the on-screen instructions until the compass

calibration is complete, taking care to keep the boat as

steady and level as possible.

The boat should not list during calibration.

If possible, you can turn the vessel in place by engaging two

engines in opposite directions.

When the compass calibration is complete, a value appears

near the Compass Cal. setting. A value near 100 indicates

the sensor was installed in a perfect magnetic environment

and calibrated correctly. If the heading performance is

unacceptable, and the value is closer to 0 than it is to 100,

you might need to relocate the sensor and calibrate the

compass again.

Select Auto Heading Alignment.

NOTE: Auto Heading Alignment is available only if there is a

GPS source connected to the NMEA 2000 network. If you do

not have a GPS source connected, you must perform the

Fine Heading Alignment instead (Adjusting the Fine Heading

Alignment, page 2).

Select Begin.

Follow the on-screen instructions until the alignment is

complete.

Adjusting the Fine Heading Alignment

If you do not have a GPS source connected to the NMEA 2000

network, Auto Heading Alignment is not available as part of

menu-based calibration, and you must adjust the Fine Heading

Alignment instead.

You can adjust the Fine Heading Alignment in conjunction with

Auto Heading Alignment to fine-tune the heading output

(optional).

From the sensor calibration screen, select Fine Heading

Alignment.

Using a landmark or a known good compass, determine the

heading of your boat.

Adjust the heading until it matches your measurement.

Select Done.

Performing Basic Calibration

If you connect the sensor to a NMEA 2000 network without a

compatible Garmin chartplotter, you must perform basic

calibration instead of menu-based calibration.

You must be able to view heading data from the sensor on a

connected chartplotter or marine display before you can perform

basic calibration. If you cannot view heading data on your

connected display, check the NMEA 2000 network and power

connections.

All other sources of heading data that are not based on GPS

must be removed from the NMEA 2000 network while

performing basic calibration.

When performing basic calibration, you first calibrate the

compass and then align the heading in one continuous

procedure. If you installed the sensor with the cable pointing

toward the bow, parallel to the keel, it may not be necessary to

align the heading.

NOTE: If you choose to align the heading, you must connect a

GPS source to the NMEA 2000 network. The boat must be able

to reach a cruising speed of at least 6.4 km/h (4 mph) to perform

the heading alignment.

Drive the boat to a location with calm, open water.

Set the display to view heading data from the connected

sensor.

Disconnect the sensor from the NMEA 2000 network or turn

off the power to the NMEA 2000 network.

Wait while the boat becomes level and stationary.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin 9 axis Heading Sensor Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin 9 axis Heading Sensor

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info