Bedienungsanleitung Garmin 9 axis Heading Sensor (Seite 3 von 4) (Englisch)

691897

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

Turn on power to the sensor, and wait until the heading data

appears on the display

Within three minutes, complete two full, slow, tight circles

taking care to keep the boat as steady and level as possible.

The boat should not list during calibration.

If possible, you can turn the vessel in place by engaging two

engines in opposite directions.

When the sensor is prepared to calibrate the compass, the

heading data disappears from the display

You may receive an error message that the heading was lost.

You can ignore this message.

Continue turning in the same direction at the same speed

for approximately 1

rotations until the heading data

appears

When the heading data appears, the compass has been

calibrated successfully, and you can align the heading

(optional).

Select an option.

• If you want to align the heading to match the front of the

boat, proceed to the next step.

• If you installed the sensor with cable pointing toward the

bow, parallel to the keel, and do not want to align the

heading, stop turning and wait, keeping the boat

stationary. Over the next two minutes the heading data

should disappear and then reappear. When the heading

data reappears, the compass should be calibrated and no

heading offset should be applied.

NOTE: If an unwanted heading offset is applied, you must

disconnect all GPS sources from the NMEA 2000 network,

and repeat the calibration. If the only available heading

display is also a GPS source, you must repeat the

calibration, and disconnect the sensor after step 7.

Continue turning in the same direction at the same speed for

approximately ten seconds, until the heading data disappears

from the display

When it is safe, straighten the boat and drive in a straight line

at cruising speed (must be at least 6.4 km/h (4 mph)) until

the heading data appears

When the heading appears, the compass has been

calibrated, and the heading has been aligned on the sensor.

Test the results of the calibration, and repeat this procedure if

necessary.

Restoring Factory Default Settings

If you relocate the sensor or do not believe the calibration was

successful, you can delete all calibration information from the

sensor, and restore its factory default settings. After restoring

the factory default settings, you must configure the sensor

before you can use it with your system.

Select Settings > Communications > NMEA 2000 Devices

> Device List.

Select the name of the sensor.

Select Review > Factory Defaults > Yes.

Specifications

Specification Measurement

Dimensions (L × W × H) 170 × 90 × 50 mm (6.7 × 3.5 × 2 in.)

Weight 200 g (7 oz.)

Temperature range From -15° to 70°C (from 5° to 158°F)

Material Fully gasketed, high-impact plastic

Water resistance IEC 60529 IPX7*

NMEA 2000 input voltage From 9 to 16 Vdc

NMEA 2000 LEN 4 (200 mA)

Compass-safe distance Negligible

*The device withstands incidental exposure to water of up to 1 m

for up to 30 min. For more information, go to www.garmin.com

/waterrating.

Limited Warranty

The Garmin standard limited warranty applies to this accessory.

For more information, go to www.garmin.com/support/warranty

.html.

Garmin

and the Garmin logo are trademarks of Garmin Ltd. or its subsidiaries,

registered in the USA and other countries.

NMEA 2000

and the NMEA 2000 logo are registered trademarks of the National Marine

Electronics Association.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin 9 axis Heading Sensor Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin 9 axis Heading Sensor

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info