Bedienungsanleitung Garmin BC35 (Seite 2 von 34) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

699110

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

BC™ 35 WIRELESS BACKUP

CAMERA

Installation Instructions

Introduction

WARNING

See the Important Safety and Product Information guide in the

product box for product warnings and other important

information.

Garmin

strongly recommends having an experienced installer

with the proper knowledge of electrical systems install the

device. Incorrectly wiring the power cable can result in damage

to the vehicle or the battery and can cause bodily injury.

When connecting the power cable, do not remove the in-line

fuse holder. To prevent the possibility of injury or product

damage caused by fire or overheating, the appropriate fuse

must be in place as indicated in the product specifications. In

addition, connecting the power cable without the appropriate

fuse in place will void the product warranty.

CAUTION

Always wear safety goggles, ear protection, and a dust mask

when drilling, cutting, or sanding.

NOTICE

When drilling or cutting, always check what is on the opposite

side of the surface.

These installation instructions do not apply to a specific vehicle

type, and are meant as a guide when installing this product on

your vehicle. For questions specific to your vehicle, you should

contact the vehicle manufacturer.

Device Overview

Item Description

Transmitter

Camera

Camera mounting bracket

Tools Needed

• Drill and 10 mm, or size X (0.397 in.) drill bit

• #2 Phillips screwdriver

• Screws, bolts, or cable ties (to secure the transmitter)

• Solderless wire-splice connector or solder and heat-shrink

tubing

• RV sealant (optional)

Installation

Camera Mounting Considerations

When selecting a location to mount the camera, observe these

considerations.

• You should test a mounting location before you permanently

mount the camera.

• Installing the camera higher on the back of the vehicle

provides a better viewing angle.

• The included bracket can be clipped onto a license plate or

other similar surface, or it can be fastened to the back of the

vehicle using the included self-tapping, panhead screws.

Transmitter Location and Wiring Considerations

NOTICE

The transmitter is not intended to be held or worn on your body

while it is in use.

When selecting a location to install the wireless transmitter,

observe these considerations.

• You should test a proposed installation location before you

permanently install the transmitter.

• Some vehicles do not provide constant minimum voltage to

the reverse lamps. You should use an automotive relay when

connecting the transmitter and camera to a power source that

does not provide constant voltage.

• Although the transmitter can transmit the video signal

approximately 45 ft (13.5 m), the location of the transmitter

can affect this range.

◦ The closer you install the transmitter to the device, the

more reliable the signal.

◦ The signal transmits from the flat front and back surfaces

of the transmitter. The transmitter provides the best

signal when either flat surface points toward the receiver.

◦ Dense metal or appliances

in the path of the transmitter

greatly reduce the transmission distance.

◦ The fewer solid objects that exist between the path of the

transmitter and the device, the more reliable the signal.

• The fuse holder located near the transmitter is not

waterproof. Installing the fuse holder in a location that is

exposed to the elements is not recommended.

• The connector between the camera and the transmitter is not

waterproof. If you make this connection in a location exposed

to the elements, you must make sure that the connection is

waterproof.

• If you are installing the camera on a boat trailer or other

location that may be exposed to water, you must waterproof

all wiring connections and the fuse holder in the transmitter

cable.

Testing the Camera and Transmitter Location

Temporarily secure the camera in the preferred mounting

location.

Temporarily place the transmitter in the preferred installation

location, and connect it to power and to the camera.

TIP: If you do not want to splice into the wiring of your vehicle

for this test, you can connect the transmitter and camera to a

12 Vdc battery.

Test the transmitter for correct operation by viewing the

camera on the compatible Garmin device.

NOTE: You may need to pair the camera to the Garmin

device before you can view the image and test the transmitter

location (Pairing the Camera with a Garmin Navigation

Device, page 3).

2 Installation Instructions

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin BC35 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin BC35

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info