Bedienungsanleitung Garmin BC35 (Seite 3 von 34) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

699110

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

If you do not see video on the Garmin device at the preferred

installation location, move the transmitter to another location

and test it again.

Repeat steps 2–3 until the transmitter operates correctly.

Test the camera view by observing the video on the device.

If the camera does not provide the optimal view for your

vehicle, move it to another location and test it again.

Repeat steps 5–6 until the camera mounting location

provides the optimal view for your vehicle.

TIP: Make note of the camera orientation when you are

testing the camera view to ensure correct permanent

installation.

Mounting the Camera

Before you permanently mount the camera, you should test the

mounting location for the optimal view for your vehicle (Testing

the Camera and Transmitter Location, page 2).

If you have already connected the camera to the bracket, you

must first disassemble it.

Place the bracket

in the mounting location.

Select an option:

• If you are mounting the bracket directly on the surface of

your vehicle, mark the locations of the two holes on the

bracket

• If you are installing the bracket on a license plate, remove

one of the license plate screws and clip the bracket onto

the license plate, aligning the hole on the bracket

with

the hole on the license plate.

Secure the bracket to the vehicle using either the included

self-tapping screws

or the license-plate screw you

removed in step 2

Place the camera in the bracket, and determine the best

place for the camera cable

to enter the vehicle.

Using an appropriate drill bit, drill a hole for the camera cable

to enter the vehicle.

Feed the camera cable through the hole and route it to the

transmitter location.

Secure the camera in the bracket using the included hex

bolts

Adjust the angle of the camera and tighten the hex bolts

using the included hex key.

Apply RV sealant around the cable where it enters the

vehicle (optional).

Installing the Transmitter

Before you permanently install the transmitter, you must test the

installation location for correct operation (Testing the Camera

and Transmitter Location, page 2).

Secure the transmitter to the installation location using

hardware appropriate for the location, such as screws, bolts,

or cable ties.

The fuse holder located near the transmitter is not

waterproof. Installing the fuse holder in a location that is

exposed to the elements is not recommended.

Connect the camera and transmitter cables.

The connector between the camera and the transmitter is not

waterproof. If you make this connection in a location exposed

to the elements, you must make sure that the connection is

waterproof.

Connect the power cable

from the transmitter to a 12–

24 VDC power source, preferably a reverse lamp

, using a

solderless wire-splice connector (not included).

NOTE: Connecting the transmitter to an always-on

12-24 VDC source (such as a running lamp) instead of a

reverse lamp requires you to manually switch power to the

transmitter. The transmitter may drain your vehicle battery if it

is left on.

If you did not use a solderless wire-splice connector, solder

and heat-shrink the electrical connections to protect them

from the elements.

Pairing the Camera with a Garmin Navigation

Device

Turn on the compatible Garmin navigation device, and bring

it within 3 m (10 ft.) of the camera.

Select Apps > Rear View.

Select Add New Camera.

Follow the on-screen instructions.

Multiple Cameras

You can pair up to 4 wireless cameras with a compatible Garmin

device. For example, you can pair one backup camera installed

on the cab and a second backup camera installed on a trailer.

See the BC

™

35 Owner's Manual for information about pairing

multiple cameras.

Appendix

Getting the Owner's Manual

You can get the most recent owner's manual from the web.

Go to garmin.com/manuals/BC35.

View or download the full owner's manual in your preferred

format.

Specifications

Camera and transmitter input

voltage

From 9 to 28 Vdc

Transmitter fuse 500 mA, fast-blow

Camera and transmitter current

usage

150 mA at 12 Vdc

Water rating (camera) IEC 60529 IPX7*

Installation Instructions 3

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin BC35 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin BC35

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info