Bedienungsanleitung Garmin Vector S (Seite 2 von 26) (Englisch)

589620

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

Vector™ Quick Start Manual

WARNING

Read all instructions carefully before installing and using the

Vector™ system. Improper use could result in serious injury.

See the Important Safety and Product Information guide in the

product box for product warnings and other important

information.

NOTICE

Go to www.garmin.com/vectorowner for the latest information

including bike compatibility, software updates, and video

tutorials.

Tools Needed

• 15 mm pedal wrench

• Bike grease

• 3 mm hex key

• 4 mm hex key

Installing Vector Components

Preparing the Crank Arms

1Confirm the compatibility of your bike at www.garmin.com

/vectorowner.

2Remove the existing pedals.

3Clean the threads, and remove old grease.

Determining Pedal Pod Clearance

NOTICE

The pedal pod should contact the crank arm only at its mounting

face, because this is the load-bearing connection. If the pedal

pod contacts the crank arm anywhere else, the pedal pod may

fracture when the pedal is tightened.

• If the mounting face À surrounding the threaded hole in the

crank arm is recessed, use one or two washers Á to fill the

recess.

NOTE: Do not use more than two washers.

• Make sure the pedal pod mounting face Â contacts the crank

arm only at its mounting face (or the washer used to fill the

recess).

If it touches anywhere else, you can use another washer to

provide the necessary clearance.

• If it is close, you can confirm proper clearance by sliding a

piece of paper between the metal bracket and the crank arm

face.

• If the mounting face of the crank arm is protruding, do not

use washers.

Installing the Pedal Pod and Pedal

NOTE: The left and right pedal pods are the same.

1Install the left pedal first.

2Apply a thin layer of grease on the pedal spindle À and the

pedal pod Á where it contacts the pedal spindle.

3On the pedal spindle, stack the pedal pod and any required

washers Â.

TIP: You must carefully bend the cable Ã out of the way.

4Insert the spindle into the crank arm Ä.

5Hand tighten the spindle.

NOTE: The left pedal spindle has a left-handed (reverse)

thread.

TIP: Power and cadence calculations are not impacted by

the orientation of the pedal pod. Garmin® recommends

placement of the pedal pod on the leading edge of the crank.

When the crank is in the forward position, the pedal pod

should be pointing downward.

6Rotate the crank arm to check for clearance.

The pedal pod should not interfere with any part of the bike.

7Use the pedal wrench to tighten the spindle.

NOTE: Garmin recommends torque of 25 to 30 lbf-ft. (34 to

40 N-m).

8Firmly plug the cable into the spindle.

9Rotate the crank arm to check for clearance.

10Repeat steps 2–9 to install the right pedal.

NOTE: If the pedal pod cable rubs the chain, you can add

one or two washers between the pedal pod and the crank

arm to increase clearance.

Installing the Shoe Cleats

NOTE: The left and right cleats are the same.

1Apply a thin layer of grease on the cleat bolt threads.

2Align the cleat À, washers Á, and bolts Â.

3Use a 4 mm hex key to loosely attach each bolt to the sole of

the shoe.

4Adjust the cleat to the shoe in your preferred position.

This can be adjusted after a trial ride.

5Tighten the cleat firmly to the shoe.

NOTE: Garmin recommends torque of 4 to 6 lbf-ft. (5 to 8 N-

m).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin Vector S Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin Vector S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info