Bedienungsanleitung Garmin Vector S (Seite 3 von 26) (Englisch)

589620

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

Adjusting the Release Tension

NOTICE

Do not overtighten the release tension screw on the bottom of

the pedal. The release tension should be adjusted equally for

both pedals.

Use a 3 mm hex key to adjust the release tension of each

pedal.

There is a window on the back of the pedal binding that

shows the allowable range.

Paring Vector with Your Edge® 1000

Before you can view Vector data on the Edge device, you must

pair the devices.

Pairing is the connecting of ANT+™ wireless sensors. This

procedure contains instructions for the Edge 1000. If you have

another compatible device, see your owner's manual, or go to

www.garmin.com/vectorowner.

1Bring the Edge device within range (3 m) of the sensor.

NOTE: Stay 10 m away from other ANT+ sensors while

pairing.

2Turn on the Edge device.

3From the home screen, select > Sensors > Add Sensor >

Power.

4Rotate the crank arm a few times.

When the sensor is paired with your Edge device, the sensor

status is Connected. You can customize a data field to display

Vector data.

Your First Ride

Before you ride with Vector for the first time, you must enter the

crank length, set the installation angle of the sensors inside the

pedals, and calibrate the static zero reference. You must also

calibrate the system if you move Vector to another bike.

These procedures contain instructions for the Edge 1000. If you

have another compatible device, see your owner's manual or go

to www.garmin.com/vectorowner.

Entering the Crank Length

The crank length is often printed on the crank arm.

1Rotate the pedals a few times in order to activate Vector.

2From the home screen, select > Sensors > > Sensor

Details > Crank Length.

3Enter the crank length, and select .

Setting the Installation Angle

Before you set the installation angles, you must set the Edge

data fields to display power and cadence.

1Go for a short ride on a trainer or on the road.

2Ride until the cadence is nearly 70 rpm.

3Accelerate smoothly to approximately 90 rpm.

When the installation angles are successfully set, a message

appears and data fields display power data on the Edge

device.

Performing a Static Zero Calibration

NOTE: During this task, the bike must be in an upright position,

and nothing can be touching the pedals.

1From the home screen, select the status bar or swipe down

from the top of the screen.

The connections page appears.

2Select > Calibrate.

When the zero reference is determined, a message appears

on the Edge device.

Calibrating Vector Before Each Ride

For best results, Garmin recommends calibrating Vector at the

start of every ride.

1Perform a static zero calibration.

2Go for a ride.

Troubleshooting

Getting the Owner's Manual

You can get the latest owner's manual from the web.

1Go to www.garmin.com/support.

2Select Manuals.

3Follow the on-screen instructions to select your product.

Vector Storage

If you are transporting your bicycle or not using Vector for an

extended period of time, Garmin recommends removing Vector

and storing it in the product box.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin Vector S Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin Vector S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info