Bedienungsanleitung Gemini 7563 (Seite 3 von 8) (Englisch)

479858

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

ALARM MEMORY

When disarming the alarm, if five turn signal flashes and five beep signals

occur (if this function have not be excluded in programming stage), it is

possible to identify the cause generating the alarm condition.

To do this, turning the ignition key in “ON” position and see at the vehicle

installed LED.

The LED will be blink, shown the last alarm condition.

The cause of the alarm will indicate for 5 times.

This indication can be interrupted by turning the ignition key to OFF.

The possible alarm signalling are indicated in the under table.

GARAGE FUNCTION

This function is used when the alarm disarming is required, e.g. for

maintenance, without any intervention to the previous programming.

In fact, this function disarms completely the alarm, without any intervention

when passive arming and against absent-mindedness arming are

programmed.

To do this, proceed as follows:

! With the alarm system deactivated, turn the ignition key to “ON” position

! The status LED will turn on for approximately 0.5”.

! During this period, put the electronic key in the specific receptacle.

! The led is turned off to indicate the alarm de-activation.

! To restore normal operating of programmed functions, arm the alarm via

the radio control.

PAG. 4

PAG. 5

PROGRAMMABLE FUNCTIONS

ACOUSTIC SIGNALS

PANIC ALARM OR CAR-FINDER

If enabled, the PANIC ALARM function allows the user to activate the visual

and audio alarm signals deliberately by pressing key 2 on the remote.

This function works regardless of whether the alarm system is “ON” or “OFF”.

The alarm signal lasts up to approx. 30”. However, you can silence it at any

time by pressing key 2 on the remote again

While the alarm signal is emitted the LED emits a continuous light.

If during the programming phase, the PANIC function has been disabled, the

CAR FINDER function will be activated.

When the alarm is activated, the CAR FINDER function allows you to obtain a

short optic/acoustic signal by pressing button N°2 on the remote.

TThis function can be useful to look for the car in a parking lot or parking silo

without creating useless alarm condition.

The brief optic/acoustic signal consists of a low beep and the simultaneous

flashing of the turn indicators.

NOTE: the emission of the audio signals is subordinate to their being enabled

when programming the accessory functions.

CURRENT ABSORPTION SENSOR

ANTI-DISTRACTION FUNCTION AND DOOR LOCKING

This function determines the automatic activation of the system if this has been

disarmed and no voluntary actions are performed by the user (e.g. Door

opening).

The function prevents the vehicle from being left unprotected in cases where,

after the arming of the system, this is turned OFF accidentally by pressing the

button N°1 of the remote control.

The self rearming is confirmed by the alarm with visual/acoustic signalling (one

flash by the turn signals and one acoustic signal) .

The anti-distraction function activates the CDL control.

Therefore, in order to prevent involuntary activations of the system, it's

MANDATORY to connect the door pin switch to the system input

(BROWN/GREN wire of the alarm wiring harness).

This function allows the user to permanently exclude all acoustic signals.

See the relative paragraph for programming.

ATTENTION: before activating of the absorption sensor, it is suggested

to consult the specific rules being in force in your country (noise

pollution).

When the absorption sensor is activated, a signal will be sent out at any

minimal tension variation in the vehicle's electrical circuit (for example lamp

switching on).

NOTE: after disarming, a door opening will stop the function.

Together with the previously described function, the automatic door locking of

the vehicle is done when running.

LED SIGNAL

CAUSE OF THE ALARM

NUMBERS OF

ALARM CYCLES

Infinite

Absorptions sensor

Doors switches

Cut wires

Positive under key (+15/54)

Trunk, hood and volumetric

sensor

External magnetic contact

LED ON (400mS)LED OFF (2 seconds)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gemini 7563 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info