479886
9
Zoom out
Zoom in
Vorherige Seite
1/9
Nächste Seite
To reset the system proceed as follows:
Switch-off power supply
hort-circuit the RED and BLACK wires of the 2-way connector
Switch the on; once the alarm system is powered, 4 acoustic signals will sound and the turn
indicators will flash 4 times
Remove the previously created short-circuit; the status LED lights up steady.
reset is confirmed by an aucoustic signal and the wailing of the siren for
approx. 3 seconds
the LED will turns off. There are no acoustic signals
!
!
!
!
!
!
system .
S LED .
system
.
Turn ignition key “ON”;
.
Turn ignition key “OFF”; .
By activating the following procedure, the system returns to the
Factory default setting.
This procedure must therefore only be used in case of need, before programming the
system or auto-learning the turn indicators flashes.
!
15.0 -
15.1 - CO
15.2 - SENSOR ADJUSTMENT
I
.
T:
.
ULTRASONIC VOLUMETRIC PROTECTION
NNECTION AND POSITIONING
nsert the WHITE connector in the “W” marked socket and the RED connector in the “R” marked
socket (see figure below).
Install the transducers of the ultrasonic sensors on the top part of the windscreen internal pillars, away
from the air vents and orient them towards the center of the rear window
o check sensitivity level proceed as follows
With the alarm system disarmed, roll down the front window about 20 cm.
Adjust trimmer at a medium setting.
Close all doors, bonnet and boot and arm the system.
During the system inhibit arming time introduce an object in the cabin through the window and
move it around; the status LED will turn off to signal a presence.
If sensitity lelvel is too high or too low, readjust the trimmer and repeat the above procedure
!
!
!
!
!
ULTRASONIC
CELLS
CONNECTIONS
SENSITIVITY
ADJUSTMENT
PAGE 16 - INSTALLER MANUAL INSTALLER MANUAL - PAGE 17
17.0 - TECHNICAL SPECIFICATIONS
Power supply
Current absorption @ 12Vdc with system armed and LED flashing
Working range temperature
Turn signals relay contact capacity
Engine immobiliser relay contact capacity
Alarm cycle duration
Maximum positive current output when armed (+A)
Maximum load of siren output
12 Vdc
15 mA
From -30°C to +70°C
8 A at 20°C
8 A at 20°C
30 sec.
700 mA
1A
16.0 - SYSTEM RESET
9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Gemini 932 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Gemini 932

Gemini 932 Bedienungsanleitung - Deutsch - 9 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info