Bedienungsanleitung Gorenje b 9010 al (Seite 15 von 17) (Englisch)

330554

Zoom out

Zoom in

Vorherige Seite

1/17

Nächste Seite

Instructions for use, installation and connection

Replacement of parts

The oven light bulb casing is under tension. Danger of

electric shock!

Before replacing the oven bulb switch off the cooker and cut it

from mains by removing the mains power fuse or disconnect

the protective device.

Remember that the bulb is regarded as consumption material

and is not covered by the warranty.

Other accessories

Oven grid, biscuit tray, etc. may be ordered from the service

center. When ordering please quote the code and the type or

model of the appliance.

Hotplate control knobs are removed by pulling them outwards

and replaced by pushing the new ones back in place.

Oven light bulb

The bulb for replacement

should meet the following

specifications:

E 14, 230 V, 25 W, 300°C.

Unscrew the glass cover by

turning it in the clockwise

direction and replace the

bulb. Screw the glass cover

back in place.

In case of side light remove

the glass cover by inserting

the screw into the slot and

move in the direction of the

arrow. (see Fig.)

Remember that the bulb is

regarded as consumption

material and is not covered

by the warranty.

Instructions for installation and connection

Safety precautions for installation

• Installation may be carried out only by qualified personnel.

• The electric installation shall be equipped with a safety

device, able to disconnect the appliance from mains in all

wires, with the distance between contacts of not less than 3

mm in open position. Good protection is provided by the LS-

switches and/or fuses.

• The connection may be carried out by rubber mains lead

(type HO5RR-F with green/yellow earth wire), PVC insulated

mains lead (type HO5VV-F with green/yellow earth wire) or

other cables of equal or better quality.

• Panels, glue and furniture lining from artificial materials,

adjacent to the appliance must be temperature resistant

(>75°C), otherwise they might be deformed.

• Remove any packaging materials (foils, artificial foam, nails,

etc.) from the reach of children, because they represent

potential danger. Children may swallow small parts, or

suffocate with foils.

Installation of electric oven

• Panels and furniture lining of the kitchen cabinet receiving

the hob must be treated with temperature resistant

adhesives (100°C), otherwise they might be discoloured or

deformed because of inadequate temperature resistance.

• Before installation you must remove the rear panel from the

kitchen cabinet in the area of installation.

• Follow the exact dimensions of the installation aperture,

indicated on the illustration.

• Bottom of the kitchen cabinet (max 530 mm) must always be

shorter than side panels in order to provide adequate

ventilation.

• Level the kitchen cabinet using the spirit level.

• Kitchen cabinet carrying the installed appliance must be

fixed to the adjacent cabinet to ensure adequate stability.

• Push the appliance into the cabinet so that screw guides

located in the oven frame holes stay on the cabinet side

panels. Be careful not to tighten the screws excessively

because you may damage the cabinet sides or the enamel

of the appliance.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gorenje b 9010 al Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info