Bedienungsanleitung Gossen Digipro F (Seite 4 von 10) (Englisch)

571659

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

GOSSEN Foto- und Lichtmesstechnik GmbH 4

3.2 Measuring functions – Ambient light measurement

Select the required ambient light function with the corresponding function buttons.

• Shutter priority in function t: a reading is taken for the corresponding aperture

(see Section 3.2.3 Shutter priority mode – Ambient light measurement, page 4)

• Contrast measurement in function t: (see Section 3.2.4 Contrast measurement, page 4)

• Aperture priority in function f: a reading is taken for the corresponding shutter speed

(see Section 3.2.5 Aperture priority mode, page 5)

• Exposure value measurement in function EV: preselect the shutter speed and the

aperture is given as an analog value (see Section 3.2.6 Exposure value EV, page 5)

• CINE (frames per second) in function t:

(see Section 3.2.7 CINE scale (frames per second), page 5)

3.2.1 Flash readings

Readings can be taken with or without synchronizing cable. When used in

conjunction with a synchronizing cable the flash is triggered by

pressing the M button–the flash is automatically triggered and measured.

• Select with the function buttons

• Adjust the desired synchronizing speed with the value buttons.

Synch range from 1 s to 1/1000 s (including 1/90 s)

• Press the measuring button M.

Digipro F is operable for metering for a period of 45 s (meter

readiness prevails as long as F remains visible in the display)

• Trigger the flash

The measured aperture (total of flash and ambient light) appears

in the left digital display, and as a flashing mark on the analog aperture scale. The aperture for the share of

ambient light is additionally indicated on the aperture scale (in our example f/8).

3.2.2 Multiple flash

Occasionally the light output from a single flash may not be sufficient to

enable you to work at the aperture desired. In that case, simply

push the top value button until the desired f/number appears in the

display. The digital display of the time t disappears and the number of

flashes required is indicated (e.g.: F4 = 4 flashes).

The Digipro F will calculate up to a maximum of 10 flash sequences.

3.2.3 Shutter priority mode – Ambient light measurement

• Select with the function buttons (the last stored value appears

on the display)

• Adjust the desired shutter speed with the value buttons

• Measure by pressing the meas. button M

The measured aperture appears in the left-hand digital display

(accuracy: 1/10 stops), also as a rounded mark in the analog aperture scale

• Select alternative aperture/shutter speed combinations with the value buttons.

3.2.4 Contrast measurement

• Select t with the function buttons

• Keep the measuring button M pressed

while aiming the meter at various areas of the subject. The analog

aperture scale displays the f-stop series between the two extreme

values and with the actual measured value flashing. The first

measured f-stop is displayed in the left-hand side of the display. It remains displayed as a reference value

(e.g. of a grey card)).

After the measuring button is released, the entire measured contrast range is displayed on the analog aperture

scale, and the last measured value will cease to flash.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gossen Digipro F Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Gossen Digipro F

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info