Bedienungsanleitung Grohe Red Duo (Seite 5 von 12) (Englisch)

626604

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

Electrical installation

Electrical installation work must only be performed

by a qualified electrician. This work must be

carried out in accordance with the regulations

according to IEC 60364-7-701 (corresponding

to VDE 0100 Part 701) as well as all national and

local regulations.

• Extension cables are not permitted between the electrical

socket and boiling water storage heater connection.

Installation

Refer to the dimensional drawing on fold-out page I.

Installing fitting, see fold-out page II, Figs. [1] and [2].

Insert fitting in sink hole. This will require leading through the

hoses one at a time.

Note: If there is no need to fit support plate (A), the clamping

length may be increased by 15mm, see Fig. [1].

Mount safety relief valve kit to the waste pipe, see Figs. [3]

to [6].

Mount wall holder, see Figs. [7] and [8].

Mount compression couplings (B) and tighten nipple, see

Fig. [9].

Fix expansion vessel (C) with safety assembly to the wall

holder, see Fig. [10].

Connect filter head and filter, see technical product

information for the filter head and the filter cartridge and fold-

out page III, Fig. [11]. Note direction of flow.

1. Install pressure hose (D) to the inlet of filter head.

2. Install sensor (E) at outlet of filter head. The sensor (E) must

be installed horizontally.

3. Install display unit (F).

Use suitable screws and wall plugs (not included in the scope

of delivery).

Connect filter system, see Fig. [12].

1. Connect adaptor (G) on the cold-water service valve.

2. Screw pressure hose (D) of filter system onto adapter (G).

3. Screw hose (H) onto sensor (E).

Connect storage heater, see Figs. [2] and [13].

Install storage heater taking into consideration the

available hose lengths.

Do not connect voltage supply yet.

Flush pipes thoroughly before and after installation

(observe EN 806).

1. Connect expansion vessel (C), see Fig. [13].

2. Screw hose (H) to expansion vessel (C).

3. Screw storage heater pressure hose (I) marked blue to

expansion vessel (C) using the seals provided.

4. Connect copper pipe (not in the scope of delivery) to

the Ø15mm compression connection (J) of the expansion

vessel (C) and tighten.

Connecting fitting, see fold-out page III, Fig. [14].

1. Screw fitting pressure hose (K) marked blue to adapter (G).

2. Screw red marked pressure hose (L) of the fitting onto the

hot-water service valve.

3. Connect the fitting pressure hose (M) marked 99 °C to

connection (N) on the storage heater.

Open the service valve and check connections for

watertightness.

Filling storage heater with water, see Figs. [15] and [16].

1. Pull button (O1) on handle (O) of fitting outward and turn the

handle anti-clockwise, see Fig. [15].

2. Fill the storage heater until water comes out the spout of

the fitting.

3. Connect voltage supply via mains plug (P), see Fig. [16].

4. Press and hold button (Q) on storage heater for at

least 2 seconds to switch on the storage heater. The red

indicator lamp (Q1) indicates that the storage heater is

switched on.

Important!

The spout must not be fitted with any downstream

resistances in the form of air bubblers (e.g. mousseurs) or

components reducing flow (e.g. restrictors) as these will

result in damage to the storage heater.

Set water hardness at filter head, see fold-out page IV,

Fig. [17].

Set water hardness at bypass setting of filter head to local

conditions, see table column A on page 4.

The relevant water supplier can provide information on the

water hardness.

The bypass value setted to the filter head must also be set on

the display unit (F), see Fig. [18].

Setting the litre specification (factory setting is 600 litre),

see Fig. [18].

The value for the litre specification depends on the water

hardness as per table column B on page 4:

The GROHE Red boiling water system is now fully

installed and ready for operation.

Button Display

Briefly press PROG button

(PRG flashes)

Briefly press RESET button to access

programming for litre specification

(00000 flashes)

Keep pressing PROG button until

required position is reached

(00000 digit flashes)

Keep pressing RESET button until

required digit is reached

(00600 digit flashes)

Keep pressing PROG button to exit

menu (PRG disappears and set value

appears)

The date of installation must be noted on the

maintenance sticker and affixed at a visible location

on the storage heater.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Grohe Red Duo Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Grohe Red Duo

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info