Bedienungsanleitung Home Easy HE-108 (Seite 1 von 2) (Englisch)

558738

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Home Easy Romote

Control Dimmer

Light Switches

V1.0

The HomeEasy series of remote control light

switchs allows you to control your lights

manually or using a HomeEasy remote

controls (Except HE-200). The dimmer

module is suitable for 1-way circuits. For 2-

way switching (or Multi-way switching)use

this master unit with any number of

dimming slave units (Contact Byrons directly

- see contact details).

RE-INVENTING THE HOME

HOME

easy

TRANSFORMERS:

- Use only with electronic transformers.

- To Calculate the Load, add the VA ratings of the transformer

(not the bulb wattage)

- Choose transformers with a maximum rating close to the lamp load

e.g. 50VA,, 60VA or 70VA to control a 50 W low voltage bulb

- Wire Wound and Toroidal transformers are not compatible with the HomeEasy

Light switch's (see compatibility), if connect the dimmer will immediately turn

off. If this occurs more than times the dimmer will block any further use, to

unblock the dimmer it will need to be disconnect from the mains supply then

reconnect (see installation guide).

Compatibility:

Compatible -

lighting products

non-compatible -

products

Over Load Protection:

The HomeEasy dimmer switch is design to self protect against over loading

and over heating, this can occur when bulbs age. The dimmer module will

automatically dim the light or turn the lights off completely until the excess

load is removed, to reset the dimmer from the protection mode switch the

lights off then on.

Installation Guide

HomeEasy Remote Control Master t:

1Gang 1-Way Circuits

Live

Lighting Load

2. Isolate the electrical supply to the lighting circuit.

3. Remove the existing switch and disconnect the wiring from the switch

terminals, take note of the wiring of the switch and the terminal markings.

Where there are two or more wires together in the old switch they must be

kept together in the new Home Easy dimmer.

4. Ensure that the wall (back) box has a minimum depth of 25mm and is free

from plaster or projecting screw heads. If using wall box with 4 fixing lugs,

the top and bottom lug must be removed to allow the dimmer switch to fit.

5. Connect the wiring as per the diagrams below, Additional slave units will

allow for 2-way operation, these additional units can only be operated

manually. Contact Byrons for your local distributor.

1. Remove the decorative front plate from the HomEasy Dimmer, place a small

screw driver into one of the side slots so that the screw driver is between the

inside edge of the front plate and the outer edge of the clear plastic and,

gently twist.

1Gang 400W Dimmer

2Gang 250W Dimmer

INSTALLATION WARNINGS:

BEFORE COMMENCING INSTALLATION

ISOLATE YOUR MAINS ELECTRIC SUPPLY

Read the instructions care fully before starting the installation process and keep

them for future reference. If you are in any doubt on the installation process,

consult a qualified electrician.

This product should be installed in accordance with the relevant sections of

the building

regulations code, and the current edition of the IEE Wiring Regulations

(BS 7671:Requirements for electrical installations) and appropriate statutory

regulations.

As of1 April 2004, new installations in the UK should be wired using the EU

harmonised colours for the supply conductors:

New colours:

 BROWN = Live  BLUE = Neutral Earth = Yellow/Green

Old colours:

 RED = Live BLACK = Neutral

Electrical installations in bathrooms, kitchens, gardens, floor and heating systems,

swimming

pools, saunas and extra-low voltage lighting are classed as special installations and

must be certified by an approved competent electrical contractor conforming to

Part P, requirements of BS 7671:2001 and appropriate statutory regulations.

Fluorescent and compact fluorescent bulbs

Wire wound and Toroidal transformers

Electric Motors

Mains Voltage GLS or cable bulbs.

Dimmable Electronic Low voltage transformers

(see Transformer section)

GU10 and equivalent HI spot mains halogen bulbs

Installation Notes:

NOTE: Certain transformer types may not operate according to their stated

power rating when used with the dimmer switch, to avoid overloading of the

dimmer it will turn down the brightness of the lights. A digital transformer or

higher rated dimmer module may be required to resolve this problem.

Live

HomeEasy Remote Control Master unit

2-Way/Mulit-Way Circuits (Slave units will not operate with a HomeEasy

Reomte Control)

Live

Lighting Load

Manual Operation Only Manual Operation Only

Slave 1

Slave 2

Live

HomeEasy Remote Control:

2Gang Dimmer Switch with 2way and 1way

Live

Lighting Load =

NOTE: When using 2 gang dimmer switch, module A must be connected to

the lighting circuit. Module A will operate independently, Module B will only

operation when module A is connected.

Slave A

Manual Operation Only

Master Dimmer

Master Dimmer A

Master Dimmer B

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Home Easy HE-108 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info