Bedienungsanleitung Honeywell CO8MS (Seite 3 von 49) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

681061

Zoom out

Zoom in

Vorherige Seite

1/49

Nächste Seite

3.2 Unsuitable locations

Do not place the CO alarm in any of the following areas.

• In an enclosed space (for example in a cupboard or behind a curtain).

• Where it can be obstructed (for example by furniture, curtains, etc.).

• In a damp or humid area, e.g. Bathrooms, Wet rooms, etc.

• Directly above a sink, cooker, steaming pots or kettles.

• Next to an extractor fan, air vent, door, window or similar ventilation openings.

• Over heat sources such as radiators or hot air vents.

• Where the temperature could drop below –10°C or rise above 40°C and never outside.

• Where dirt or dust could block the sensor.

• Near paint, thinners, solvent fumes or air fresheners.

If locating the CO alarm in a room with a fuel burning appliance (see ﬁgure 1)

• If the alarm is mounted on a wall, it should be located at a height greater than the height

of any door or window but still be at least 15 cm from the ceiling.

• If it is mounted on the ceiling it should be at least 30 cm from any wall or light ﬁtting.

• The CO alarm should be a horizontal distance of between 1m and 3m from the potential

CO source.

• If there is a partition in the room, the CO alarm should be located on the same side of the

partition as the potential source.

• In rooms with sloped ceilings, the CO alarm should be located at the high side of the

room (see ﬁg 2).

If locating the CO alarm in a bedroom or in rooms remote from a fuel burning

appliance (see ﬁgure 3)

• Mount the CO alarm relatively close to the breathing zone of the occupants.

Whatever position is chosen make sure it is possible to view the three light indicators, when

in the vicinity of the alarm.

WARNING: Do not use the CO alarm on an intermittent basis, or as a portable

detector.

4 Installation Procedure

1. Select a suitable location (paragraph 3.1).

2. Remove the mounting plate from the packaging/alarm.

3. Place the mounting plate on the ceiling or wall exactly where you want to mount the

alarm. With a pencil, mark the location of the two screw holes.

4. Take care to avoid any electrical wiring already present in the ceiling or the wall; drill

holes using a 5.0mm drill bit through the centre of the marked locations. Push the

plastic screw anchors provided into the drilled holes. Screw the mounting plate to the

ceiling or wall.

5. Do not mount the cover on the base when switch is on position “X” (ﬁgure7).

6. Carefully line up the alarm on the base, then press home & twist on (this connects the

batteries). The red, amber & green lights will immediately ﬂash in sequence to show

they are working.

7. Press the test button (after 15 seconds) to ensure that the alarm works.

8. Install all the other alarms similarly.

4.1 How to tamperproof the alarm

It is possible to protect against unauthorized removal of the alarm. Break off the small pillar

on the base of the alarm as shown in ﬁgure 4. To remove the alarm, use a small screwdriver

to release the catch (push the catch towards the ceiling) and then twist off the alarm

(ﬁgure 5).

If necessary it is possible to further secure or tamperproof the alarm by using a No.2 or No.4

self tapping screw (2 to 3mm diameter by 6 to 8mm long- not supplied), to ﬁrmly lock the

alarm and its mounting plate together (ﬁgure 6).

5 Registering the Detector

Registration is the procedure that associates the detector with the evohome security hub.

2. Remove and re-ﬁt the unit to the wall mount.

3. A conﬁrmation message appears after several seconds (up to 10 sec), indicating

registration of the sensor at the evohome security hub.

4. Two beeps will conﬁrm the successful enrolment. always register a sensor in its ﬁnal

position.

Note: The switch on the PCB is for manufacturing purposes only (this is not for

registration).

https://

WEB*

*https://international.mytotalconnectcomfort.com

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Honeywell CO8MS Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Honeywell CO8MS

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info