SETTING YOUR PROGRAMMER
SETTING THE CORRECT TIME
To set the correct time, open the ap on the front
of the programmer.
STEP1
Move the setting
slider to the SET
TIME position. The
time on the display
will now be ashing
to indicate it can be
changed.
STEP 2
To change the time, press the + or
-
buttons until
the correct time is displayed.
Each press of the button will change the time by
one minute. Holding the button down for more
than a few seconds will change the time slowly at
rst, then quickly.
STEP 3
Moving the setting slider to the next position com-
pletes setting the time.
SETTING THE HOT WATER PROGRAMME
The hot water programme has two ON/OFF
switching times per day. Each time can be set
between 3.00 am and 2.50 am (on the next day)
to allow you to programme the hot water to stay
on past midnight, if required.
STEP 4
Move the setting slider to the SET HOT WATER
position. The words HOT WATER will now be vis-
ible on the display and the rst ON time will now
be ashing.
STEP 5
Use the + and
-
buttons to set the rst ON time.
Each press of the button will change the time by
10 minutes.
STEP 6
Press the NEXT ON/OFF button once to display
the rst OFF time. Set this time using the + and
-
buttons.
STEP 7
By pressing the NEXT ON/OFF and + or
-
but-
tons the remaining ON/OFF times can be set.
*NOTE*
1. When pressing the + button, the next ON or
OFF marker may start to ash. If this hap-
pens the next programme time will have been
changed. Press the NEXT ON/OFF button to
check and adjust this programme time if nec-
essary.
2. When pressing the
-
button, the previous
ON or OFF marker may start to ash. If this
happens the previous programme time will
have been changed. Follow the procedure
in “REVIEWING PROGRAMME TIMES” to
check and adjust this time if necessary.
Moving the setting slider to the next position com-
pletes setting the hot water programme.
SETTING THE HEATING PROGRAMME
The heating programme has two ON/OFF switch-
ing times per day. Each time can be set between
3.00 am and 2.50 am (on the next day) to allow
you to programme the heating to stay on after
midnight if required.
STEP 8
Move the setting slider to the SET HEATING posi-
tion. The word HEATING will now be visible on
the display and the rst ON time will be ashing.
STEP 9
The required heating programme can now be set
by following the same procedure as “SETTING
THE HOT WATER PROGRAMME” in steps 5 to 7.
STEP 10
Moving the setting slider to the next position com-
pletes setting the heating programme.
REVIEWING PROGRAMME TIMES
To review your hot water programme move the
setting slider to the SET HOT WATER position.
To review your heating programme move the set-
ting slider to the SET HEATING position.
To review the programme times press the NEXT
ON/OFF button repeatedly. Any of these times
can be adjusted by using the + and
-
buttons.
+ AND
-
BUTTONS
LCD
DISPLAY
ON/OFF
MARKER
HOT WATER
INDICATOR
OVERRIDE
BUTTONS
HEATING
INDICATOR
EXTRA HOUR
BUTTONS
HEATING
SLIDER
SETTING
SLIDER
HOT WATER
SLIDER
NEXT ON/OFF
BUTTON
RESET
IF DISPLAY REMAINS BLANK AFTER SWITCH ON - PRESS RESET
3.00am
4.00am
5.00am
6.00am
7.00am
8.00am
9.00am
10.00am
11.00am
12.00am
1.00pm
2.00pm
3.00pm
4.00pm
5.00pm
6.00pm
7.00pm
8.00pm
9.00pm
10.00pm
11.00pm
12.00pm
1.00am
2.00am
3.00am
HOT WATER
HEATING
BUILT-IN PROGRAMME
3.00am
4.00am
5.00am
6.00am
7.00am
8.00am
9.00am
10.00am
11.00am
12.00am
1.00pm
2.00pm
3.00pm
4.00pm
5.00pm
6.00pm
7.00pm
8.00pm
9.00pm
10.00pm
11.00pm
12.00pm
1.00am
2.00am
3.00am
HOT WATER
HEATING
PERSONAL PROGRAMME
