Bedienungsanleitung Humax HDR-1003S (Seite 34 von 40) (Englisch)

604917

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

AU34

Trouble Shooting

Before contacting the customer service centre, make sure to read the tips

below carefully. If the problem persists after you complete the following

procedure, please contact HUMAX Australia Customer Service for further

instructions.

1. No message is displayed on the front display. (The product will not

switch on.)

• Check the main power cable and make sure it is plugged into a suitable

power outlet.

• Check that the mains supply is switched on.

• Connect the power cable to a dierent power outlet.

• Check that the power switch is on at the rear of the product. (where

applicable)

2. No picture

• Make sure that the product is powered on and in operation mode. (Press

the STANDBY button)

• Make sure that the AV cable is rmly connected to the TV.

• Make sure that the antenna cable is properly connected to the product.

• Be sure to activate channel search.

• Check the brightness level of the TV.

• Check if the channel is currently on air.

• Make sure that STB or PVR is selected as input on the remote control.

• Make sure that the antenna setting in the menu is correct. (satellite only)

3. Poor picture/sound quality

• Make sure there is no mobile phone or microwave oven near the product.

• Keep the power cable and the RF cable apart from each other.

Note: If the antenna is covered with snow or the RF is weakened by heavy rain, the

condition of the sound and picture may temporarily be poor. However, poor

sound and picture quality due to weather conditions cannot be accepted as a

malfunction of product.

[Satellite]

• Change the satellite dish for a larger one as this will increase the signal

levels received.

• Replace the LNB with a lower noise factor in case the noise factor is too

high.

• Replace the LNB with a new one in case it is damaged or out of order.

• Install the antenna in an obstacle-free place.

• Check the signal levels and adjust your antenna if the level is too low. The

signal level may be aected by weather conditions.

4. No or poor sound

• Check that your AV cable is connected correctly.

• Check the volume levels of your TV set and the product.

• Check if the product or TV is on mute.

• Check audio type or soundtrack option. (where applicable)

5. Remote control does not operate.

• To control the product, the top end of the remote control should point

directly towards the receiving part of the product.

• Remove and reinsert the batteries in the remote control.

• Replace the batteries in the remote control for a new set.

• Set the remote control to STB or PVR mode, if you are using the universal

remote control. (where applicable)

6. Cannot make reservations.

• Check that no previous reservations are conicting with the new

reservation.

7. No password information is given.

• The default password is 1234.

8. Channel search does not work.

• [Satellite] Make sure that the antenna setting in the menu is correct.

9. Cannot update new software.

• If the product does not show a message requesting update, this means no

software is available.

Appendix

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Humax HDR-1003S Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info