521912
17
Zoom out
Zoom in
Vorherige Seite
1/20
Nächste Seite
32 33
- If you want to remotely select the last/next song, or pause/
play, it needs your Bluetooth mobile phone or Bluetooth
transmitter need to be paired with the headset to support
the AVRCP prole. Refer to the user’s manual of your mobile
phone or Bluetooth transmitter for further information.
- The Bluetooth will disconnect the headset and the mobile
phone automatically if you plug in 3.5 mm audio input, and
the line in is available at the time.
6. LED Indicator
1) Charging
7. Indication Tone
8. Factory Reset
In the status of turned off, long press MFB and pause buttons
for 8 seconds simultaneously and don’t release them until the
red and blue LED indicators are on.
9. Resetting
If the product works abnormally, you can plug a 3.5 mm Line-in
or charge the headset so that it resets the product.
Care and Maintenance
Read the recommendations below carefully before using the
“BTH-033”. By following these you will be able to enjoy this
product for many years.
- Keep it dry and don’t put it in a dump place, to avoid the
product’s internal circuit being affected.
- Keep the product away from direct sunlight or hot places.
High temperatures will shorten the life of electronic devices,
destroy the battery or distort certain plastic parts.
- Don’t expose the product to cold areas. It may damage the
internal circuit board.
- Don’t try to disassemble the product as it may get damaged.
- Don’t let it fall down on to the oor or on other hard surfaces.
The internal circuit might get damaged.
2) Pairing with Bluetooth Device
LED indicator Status of headset
Red LED on Charging
Red LED off Finished charging
LED indicator Status of headset
Red and blue LED indicator
ashes alternately
Pairing mode
Blue LED indicator ashes
once quickly every 2 seconds
Not connected device
Blue LED indicator ashes
twice quickly every 4 seconds
Have already connected HFP
or A2DP
Blue LED indicator ashes
three times quickly every
4 seconds
Connect HFP and A2DP
simultaneously
Blue LED indicator ashes
quickly
Calling/incoming call
Blue LED indicator ashes
once quickly every 4 seconds
During a call
Indication tone Status of the headset
Continuous two prompt tone
every 10 seconds
Conversation mode and
microphone mute
Three ‘dong’ warning sounds
every 30 seconds
Low battery
Blue LED indicator ashes
once quickly every 4 seconds
Low battery
17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für I-onik BTH-033 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info