Bedienungsanleitung Irox HBR555 (Seite 22 von 24) (Deutsch, Englisch, Französisch, Italienisch)

578938

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

70 71

6968

4c) MAXIMUM AND MINIMUM

TEMPERATURES AND HUMIDITY

The maximum and minimum recorded indoor temperature,

humidity and outdoor temperatures will be automatically

stored in memory. To display them, Press [ MEM ] once

to display the maximum readings and again the minimum

readings. The respective indicators,

[ MAX ] or [ MIN ] will be displayed.

To clear the memory, hold down [ MEM ] for two seconds.

The maximum and minimum readings will be erased.

If you press [ MEM ] now, the maximum and minimum

readings will have the same values as the current ones until

different readings are recorded.

4d) TEMPERATURE ALARM

Weather Station is equipped with a temperature alarm

whereby a user-defined temperature can be selected.

When the selected temperature is reached an acoustic alarm

will be initiated. Temperature alarm is programmed as

follows:

1. Press the [TEMP ALARM] button.

2. Hold the [TEMP ALARM] button for 2 seconds.

3. Select the desired temperature for the alarm by using the

[ ] or [ ] buttons.

With one further pressing of the TEMP ALARM button

the data entered is confirmed.

4. THERMOMETER / HUMIDITY

4a) HOW TO CHECK REMOTE AND

INDOOR TEMPERATURES

The wave display on the outdoors temperature indicates the

reception of the remote unit is in good order. If no readings

are received from the remote unit for more than two minutes,

blanks “ ” will be displayed until further readings are

successfully searched. Check the remote unit is sound and

secure. You can wait for a little while or Hold [ ] for 2

seconds to enforce an immediate search. If the temperature or

humidity goes above or below than the measuring range of

the main unit or the remote unit (stated in specification), the

display will show “ ” & “HHH” or “LLL” respectively.

The unit can be set to automatically scan and display

readings from the remote sensors, the display will show

the readings from one channel for about 4-seconds and

then proceed to the next channel display.

-To activate the remote-sensor scanning mode:

Press and the hold the button [CHANNEL] for 2 seconds.

-To deactivate the remote-sensor scanning mode:

Press and the hold the button [CHANNEL] for 2 seconds.

3b) BAROMETRIC PRESSURE TREND

The atmospheric pressure indicator, in the weather forecast

window, uses arrows to indicate if the atmospheric

pressure is increasing, remaining stable, or decreasing.

3. WEATHER FORECAST

3a) WEATHER FORECAST

The unit is capable of detecting atmospheric pressure

changes. Based on collected data, it can predict the weather

for the forthcoming 12 to 24 hours.

3b) Weather Forecast Alert

A weather forecast alert alarm will go on when the

weather forecast change to one of the status below:

Heavy rain, heavy snowy or unstable stormy weather.

The Weather Display backlight will be lighting up 2

minutes, the beep sound turns on and the storm symbol

will be shown on the display. To deactivate the

sound alert switch the [ALERT] button to “OFF”.

Arrow

indicator

Pressure

Trend

Steady FallingRising

NOTE:

1. It is not necessary and not possible to adjust the altitude

of the weather station. After the initial start-up of the

weather station, a first forecast will be made within the

first 24 hours of operation.

2. In periods of long stable weather conditions, it becomes

difficult to make a reliable forecast.

3. The weather forecast is solely calculated on the basis

of barometric air pressure changes.

4. The probability of a correct weather forecast is

approximately 70% and is valid for an area of approx.

20-30 km around the location of the weather station.

5. The forecast “Sunny” means at night “cloudless

weather”. Fogies not indicated by the weather station

as this can occur with different weather conditions.

6. If you travel with become impossible due to changes in

altitude and location. You'll have to wait up to 24 hour

so that the weather station can calculate a new forecast

based on the conditions at the new location.

Forecast

Symbols

Sunny Slightly Cloudy Cloudy

Snowy heavy snowyHeavy rainyLittle rainy

The unit is in searching mode.

Temperature readings are

securely registered.

No signals.

˚C

4b) HOW TO READ THE KINETIC WAVE DISPLAY

The kinetic wave display shows the signal receiving

status of the main unit. There are three possible forms:

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Irox HBR555 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info