GSM pager CA-1202 „Athos“ 2/4 MHF52705
Figure 1: installation of the GSM pa ger in Mode 3
6.1 Programming sequences
Enter the prescribed spaces in SMS texts as shown in the table below. MASTER is a factory default master code, which should be changed to your own
password. All SMS texts are case insensitive.
* See part 5 for details.
SIM entry* Text of SMS instruction Descrip tion
RESET EN 3 MASTER RESET EN 3 Mode setting. Factory default is 0 – no function (im m ob il i za t io n r el a y c op ie s i g ni t io n) . Note: By
performing the RESET EN x instruction, all settings, remote controllers and enrolled wireless detectors
will be erased! RESET is indicated by four siren chirps.
Not possible MASTER UC uuuu
User Code setting – the code (password) allows you to operate the alarm remotely via SMS from
unauthorized phones. uuuu is a new user code, up to 8 characters (A –Z & 0 – 9). Factory defau lt
user code is USER
Not possible MASTER MC xxxx Master Code setting, xxxx is a new master code, up to 8 characters (A –Z & 0 – 9).
The code allows you to change settings of the GSM pager. Factory default master code is MASTER
TEL1 xx...x MASTER TEL1 xx...x
TEL2 xx...x MASTER TEL2 xx...x
TEL3 xx...x MASTER TEL3 xx...x
TEL4 xx...x MASTER TEL4 xx...x
Setting of phone numbers to re port alarms (these phones will also be authorized to control the
GSM pager via SMS without a user password)
E.g.: MASTER TEL2 +420602123456 will enter the phone number into the TEL2 memory
MASTER TEL3 0 will erase the TEL3 memory.
DIAL1 xx...x MASTER DIAL1 xx...x
DIAL2 xx...x M ASTER DIAL2 xx...x
DIALA xx...x MASTER DIALA xx...x
DIALB xx...x MASTER DIALB xx...x
Setting of phone numbers to dial using Hands free.
E.g.: MASTER DIAL2 +420602123456 will enter the number into the DIAL2 memory (which is dialed
after you press button 2 on the remote control)
MASTER DIAL2 0 will erase the memory DIAL2.
DIP abcdefghij MASTER DIP abcdefghij DIP parameter entry – see part 7
SET abcdefghi M ASTER SET abcdefghi SET parameter entry – see part 8
Not possible MASTER LEARN RC Remote Control enrollment - up to 4 controllers can be enrolled, turn the ignition key on before
sending the instruction. To enroll a remote control press and hold buttons A and B together for 3
seconds. After you enroll all remote controls, turn the ignition key off.
Not possible MASTER TXT 01,text Editing of SMS texts (reports and instructions), see part 10
TELU xx...x M ASTER TELU xx...x Sustain call setting (for pre-paid cards) 1 x a month the xx..x numb er is called, call duration 10 s.
GSM pager CA-1202 „Athos“ 3/4 MHF52705
7 DIP parameters
By SMS: MASTER D IP ABCD EFGHIJ you can change 10 features:
Description
DIP
0 1
A no function in Mode 3 (s et to 0)
B Silent alarm
Audib le alarm (30 sec.)
C
SMS alarm report only
SMS alarm report + siren sound
phone call
D SMS remote control not
confirmed by SMS reply
SMS remote control instructions
confirmed by SMS repl y
E no function in Mode 3 (s et to 0)
F no function in Mod e 3 (set to 0)
G
User can not cha nge SMS
texts
User can chan ge SMS texts by TXT
sequence
H no function in Mode 3 (s et to 0)
I
0 = Immob ilizatio n by armin g and b y SMS in struction
1 = Immobilization by arming and automat ically 5 minutes after igniti on is
turned off and also by SMS instruction
2 = Immobilizati on only by SMS instruction
J
Self-location disabled
The car´s lo cation will be sent by
SMS to num bers TEL1 to T EL4 if
there is an alarm or if the ca r stops
after the immob ilization SMS
instruct ion (See 13. 6.)
Factory default setting is DIP 1111000000 (bold letters in the text). If you
want to change only particular parameters, enter x for the others (i.e.
MASTER DIP x0xxxxxxx x).
8 SET parameters
By SMS: MASTER SET ABCDEFGHI you can change 9 features:
Description
SET
0 1
A no functi on in Mode 3 (s et to 0)
B no functi on in Mode 3 (s et to 0)
C no function in Mode 3 (set to 0)
D
Instant activat ion input logic:
0 = automa tic
1 = activated b y falling edge (grounding)
2 = activated b y rising edge (disconnecting from GND)
E INP1 logic:
0 = automa tic
1 = activated b y falling edge (grounding)
2 = activated b y rising edge (disconnecting from GND)
F no function in Mod e 3 (set to 0)
G no function in Mode 3 (set to 0)
H no function in Mode 3 (set to 0)
I
Do not switc h off the GSM
module
Switch off the GSM module
after 30 m inutes of idle
Factory default setting SET 100000010 (bold letters in the text).
If you want to change only particular parameters, enter x for the others
(i.e. MASTER SET xxx0xxxxx) .
9 User instructions
9.1 Remote control b y SMS instructions
SMS instruct ions sent from an authorized phone (T EL1 to TEL4) can o perate
the GSM pager remotely . Factory default instr uction texts are shown in the
following table. The instruction te xts can be chan ged by SMS text editing,
see pa rt 10.
If an SMS is sen t from an unauthorized phone (o ther than TEL1 to TEL4), a
valid user code must be entered bef ore the instructio n (e.g. USER IMO) .
SMS text Description
IMO
STOP (immobilize) the car (after turning the igniti on key off)
UNIMO
Unblock (mob ilize) the car
STAT US
The GSM pager w ill reply with st atus information, e.g. “ca r
reports: Time: 27 .01.04 13:04, S tatus: Armed, Unbloc ked,
Igniti on off“.
HELP
The GSM pager w ill reply with a brief list of SMS
instruction s.
UC uuuu
To change the user code. uuuu is the new user code , up to
8 characte rs (A –Z & 0 – 9). Facto ry default u ser code is
USER
CREDI T
To obtain t he balance of a prepaid S IM card if used. See
13.5 for d etails
HF abcdef
Hands-fre e set adjustm ent:
a – enable cal ls (0= disabled , 1=enabled)
b – auto ans wer inco ming calls (0= disabled , 1=enabled)
c – micropho ne sensitiv ity 0 to 9, (5)
d – speaker volume 0 to 9, (5)
e - ringing t one volume 0=m ute to 9=max ., (5)
f – ringing sound 0 to 9, (5)
LOCATOR
To obtain the car location f rom the GSM prov ider. See 13 .4
• Th e parameters in bold a re factory defau lts.
• Th e instruction m ust contain spaces as shown in the table
• Only basic ASCII can be used in the SMS instruction texts
• If t he SMS text contains the % sign, then the following text will be ignor ed.
9.2 Phone calls by an installed han ds free set
If the optional HF-03 hands free set is installed, it is possible to receive
and make phone calls via the GSM pager. When the igni tion key is on ,
the remote control (RC-40) allows you to operate the hands free set.
Incoming calls – to answer them, press any button on the RC-40 remote
control. By pressing any button again, the call will be termina ted.
When armed, all incoming calls are automatically rejected. I f the car is
blocked (by IMO instruct ion) all calls are automat ically answ ered (it is possible
to listen and to speak to the car remotely). Automa tic call answering w hile you
are driving can a lso be enabled by t he HF instruction (see 9.1).
To make a call – you can ca ll up to 4 preprogrammed numbers while you are
driving. By pressing butt on A, B, 1 or 2 on the re mote control you will dial the
corresponding number (pre- programmed by DIAL A to DIAL2, see 6.1)
9.3 Alarm
When an alarm is triggered, t he siren will soun d for 30 sec., warning SMS
messages will be s ent to all phones (TEL1 to TEL4) and these phones wil l
also be called wit h the siren sound.
10 SMS text editing
The SMS texts (alarm information and instructions) are factory
preprogrammed. However, it is possible to change these texts by a
mobile phone or via internet access using www.GSM link .cz
To change a text by mobile phone, send the SMS:
MASTER TXT zz,text,zz,text,…
where: zz is the text index (see the following table)
text is y our n ew text – up to 30 characters, full stop (dot) or
comma cannot be used in the text, spaces are allowed
Example: MASTER TXT 01,LOCK PLEASE
By changing text numbers 01 to 16, you will modify the control SMS
instructions. This allows you to customize the remote control of t he car.
You can also make your own password part of the instruction to in crease
the security of the mobile phone remote access.
10.1 SMS text table
zz Factory default text zz Factory default text
SMS commands:
34 Wir eless detec tor
01 AM 35 Current detector
02 DM 36 T elep hone 1
03 IMO 37 Telephone 2
04 UNIMO 38 Telephone 3
05 STATUS 39 Telephone 4
06 H ELP 40 T elephone - UC
07 C REDIT 41 Telephone - MC
08 DIAL 42 Remote controller
09 HF
Status infor mation:
10 L OCATOR 50 C ar alarm repo rts:
11 MC 51 Status:
12 UC 52 Armed
13 DIP 53 D isarmed
14 TEL 54 Igniti on key ON
15 L EARN RC 55 Igni tion key OFF
16 LEARN JA 56 Engine is block ed
17 SIREN 57 Engine is unblocked
18 SET 58 N o alarm
Event s:
59 Alarm timeout
20 A larm 60 Low accumulat or voltage
21 A larm cancel ed by a user 61 Power failur e
22 F ire alarm 62 Power recov ery
23 T amper alarm 63 Time:
24 D isarming 64 Low batt ery voltage
25 A rming
Confirmation SMS:
26 L ow battery v oltage 70 C ommand acc epted
27 E ngine is block ed 71 C ommand syntax error
28 E ngine is unblocked 72 New MC code:
Source:
73 New UC code:
30 Ignition key 74 Reset
31 Door co ntact 75 Regis tered phone number:
32 INP1 activation 76 Credit:
33 IN P2 activation 77 LEARN mode, enr olled
The gray texts are not available in mode 3.