Bedienungsanleitung Jablotron GD-06 (Seite 1 von 5) (Englisch)

554883

Zoom out

Zoom in

Vorherige Seite

1/5

Nächste Seite

GSM communicator GD-06 Allegro – complete manual 1/5 MHG 51203

GSM communicator GD-06 Allegro

Complete manual

The GD-06 ALLEGRO is a universal GSM dialer and controller. It can

be used for both home and industrial automation purposes, for security

applications or remote data transfer projects. There are 6 terminals and

1 output relay, each of the terminals can be independently set as input

or output. Triggering of any of the inputs will cause the sending of a

reporting SMS message to preprogrammed phone numbers or a direct

call to a telephone number. By using SMS text messages, you can

switch on or off the remote controlled outputs. In the basic (factory

default) setting, the GD-06 provides 4 inputs and 3 outputs.

The device can be programmed using programming SMS messages or

via the Internet using Jablotron’s GSMLink web page.

For most application the basic description in chapters 1 and 2 will be

sufficient. Following parts of the manual (starting with chapter 3)

describe full programming of all inputs and outputs, triggering a

monitoring mode, GPRS data communication and analogue data

transmission.

1. Specification

Power supply voltage 8 - 15 V DC

Current consumption 20 mA (stand-by), 500 mA (maximum)

GSM band E-GSM/GPRS 900/1800MHz (2 W @

GSM900, 1 W @ GSM1800)

Terminals (P1 - P6): Input mode - triggered when

connected to GND (200 ms filter is

used)

Output mode - transistor output (max.

100 mA), switches to GND

Relay output over-switching contact (NC-C-NO),

max. 2A / 24V

Dimensions 76 x 110 x 33 mm (antenna - 125 mm)

Complies with EN 60950, EN 301489-1, EN 301489-

7, EN 301419-1, EN 301511

Hereby, Jablotron Ltd., declares that this GD-06 complies with the

essential requirements and other relevant provisions of Directive

1999/5/EC.

Original conformity assessment can be found at the web page

www.jablotron.com, section Technical support.

2. Installation and basic functions

2.1. Installation

SIM

MASTER

HANDS FREE

CONNECTOR

INDICATION

LED

TEMPERATURE

SENSOR

MASTER

Figure 1

The GD-06 ALLEGRO is designed for indoor use only. Check the GSM

signal strength before installing the Allegro (e.g. with a GSM phone

using a SIM card for the same operator).

1) Insert a SIM card into a GSM phone and disable its PIN. If you

cannot disable it, set it to 1234.

2) Insert the SIM card into the GD-06.

3) Connect the power supply.

4) The LED will start flashing until the SIM card registers into the

GSM operator’s network (max. 1 minute).

Standby mode is then indicated by short flashes of the LED

(approximately. once every 2 sec). If the LED is lit permanently, GSM

communication is in progress.

2.2. RESET EN

Reset the GD-06 communicator to the factory default settings with

English communication by sending the instruction “MASTER RESET

EN” to the dialer. The factory default setting after Reset EN is shown in

tab. 1.

Setting of the communicator after MASTER RESET EN

P1, P2, P3, P4

Connecting or disconnecting to GDN will trigger

sending SMS information to all telephone numbers

TEL1 – TEL6.

Example: "P1 On" or “P2 Off"

SMS instruction sent from TEL1-TEL8 telephone

numbers controls the outputs.

Example: " ON P5 " or “OFF P6 "

RELAY

(NO,C,NC)

Relay switches over (on/off/on…) whenever a

phone call from TEL1 or TEL2 is detected.

TEL1,… TEL8 All numbers are erased

Access codes Set to USER and MASTER

Time to answer

the incoming call

Set to 10 seconds

tab. 1

2.3. Basic (quick) setting

Setting can be easily made via Jablotron’s web page www.gsmlink.cz

(see chap. 6) or by sending SMS messages from a mobile phone.

This section will describe only the basic setting of the GD-06 after

performing RESET EN command, described in tab. 1.

Store the TEL1 to TEL8 telephone numbers using the below

programming SMS instruction sent from a GSM phone:

MASTER TELX YYY ZZZZZZZZZZZ

Parameter Value Description

X 1,2,3,4,5,6,7,8 Memory position for TEL1 to TEL8

SMS

Instruction to send SMS to this

number

YYY

SMS+

Instruction to send SMS to this

number first and then to call this

number

ZZZZZZZZZ

Telephone number (max 20 digits) ,

“+” prefix can be used for

international calls

Example: “MASTER TEL1 SMS 00420483559911”

You will then receive a confirmation message from the GD-06 to your

mobile phone.

Notes:

• There must be spaces between the parameters. The SMS

instruction is case insensitive.

• For telephone numbers TEL7 and TEL8, which are used for

remote control only, you can use any YYY parameter.

• To delete a telephone number, send the SMS instruction

“MASTER TELX DEL”, for example “MASTER TEL3 DEL”.

• If the confirmation message is not in English, reset the GD-

06 as described in paragraph 2.2.

After installation of the ALLEGRO and programming of the telephone

numbers, the GD-06 is ready for operation.

• Triggering of any input P1 to P4 will cause the sending of an SMS

report to the telephones stored in the positions TEL1 to TEL6.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Jablotron GD-06 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Jablotron GD-06

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info