Bedienungsanleitung Jablotron GD-06 (Seite 4 von 5) (Englisch)

554883

Zoom out

Zoom in

Vorherige Seite

1/5

Nächste Seite

GSM communicator GD-06 Allegro – complete manual 4/5 MHG 51203

51 On

52 Off

60 P6

61 On

62 Off

70 Relay

71 On

72 Off

GD-06 reports description of device -

for example „COMPRESSOR

ROOM REPORTS“

81 Event

82 Status

83 SMS syntax error

Setting has been

done

Command has been

done

GSM network

recovery

Power supply

recovery

88 Credit

89 Credit request failure

90 GSM level signal

tab. 5

4. Setting of special functions

4.1. HF-03 hands-free set

Connected HF-03 hands-free set cannot be used for making direct

phone calls from Allegro. But by incoming SMS message “USER

(MASTER) CALL”, DTMF code or activation of input can be activated

“monitoring mode”. This can be especially used for listening to the area

in case of alarm.

MASTER HF M,S RING T,V,E DTMF XXXX

Where:

M Volume of microphone (0 to 9)

S Volume of speaker (0 to 9)

T Setting of ringing before phone call will be received (0-60sec.)

V Volume of ringing (0-9)

E Melody of ringing (0=without melody, 1-10 melodies)

XXXX Setting of DTMF code (up to 10 figures) for switching the

incoming phone call to the monitoring mode. It is important to

enter DTMF codes without any repetition in their sequencing.

For example If there is code 123, it is not possible to use

another code 12345 - after receiving the initial 123 it is

recognized as the correct code, the command will be

performed and 4 will be considered as the beginning of a new

code.

If there is no DTMF code used (neither for HF, nor for operating of

terminals P1-P6 or RELAY), the incoming phone call is switched to

monitoring mode immediately (except the calls made from phone

numbers preset for controlling the Allegro by dialing-in 5.2.).

MASTER HF 3, 4 RING 20, 5, 1

- Allegro receives a phone call in 20 seconds, it will ring using melody

number 1 at volume 5. Volume of the microphone will be at level 3

and the volume of the speaker will be at level 4.

4.2. Credit balance

MASTER (USER) CREDIT parameters

The Allegro can send information about the credit balance of a

prepaid SIM card. An SMS sent from any of the stored numbers

containing the word CREDIT followed by the correct instruction

(different for every provider) will result in the sending of the information

about the credit. Please ask your mobile phone provider for more

information.

MASTER (USER) CREDIT uuuuu

Where uuuuu is a string, which depends on the GSM provider. Ask

your provider for more details

If you want to check the credit regularly use the following sequence.

CREDIT uuu..u xx yyy zz

Where: uuu…u is the instruction given by the provider for receiving

information about the amount of credit

xx is the time period (in days) for checking.

yyy is minimum level of credit

zz is a position of the credit in the information SMS sent

by the provider

- If the level of the credit is lower than set value (yyy) the information

will be sent to the telephone numbers that have the ERROR setting

preset (see 4.4.).

4.3. Sustains calls

MASTER TELP

If a prepaid card is used, the dialer can automatically perform a sustain

call when there was no call within a 3 month period. It will dial the

programmed number and after 10 second call duration the dialer will

hang up. The number, which should be called, can be entered by:

MASTER TELP 14112

- phone call to number 14112 is made every three months

4.4. Error reports

ERROR TX

Command is used for programming the numbers to which error

messages are sent – after failure of power supply, failure of GSM

network and low credit of pre-paid card. Messages will be sent after

restoration of communication. Failure of GSM must be longer than 15

minutes. Command: MASTER ERROR DEL will cancel sending of the

error messages.

MASTER ERROR T1 T7

- to send information about errors to phone numbers TEL1 and TEL7

4.5. GPRS setting

MASTER GPRS APN, NAME, PASSWORD, CONFIRM

If it is required to get access to www.gsmlink.cz or to send data in

GPRS format it is necessary to set proper parameters first. Parameters

can be different for every GSM provider. For details ask your GSM

provider.

APN Access point name (e.g. Eurotel in The Czech Republic

has APN “internet”)

NAME user name (it may not be required by operator)

PASSWORD user password (it may not be required by operator)

CONFIRM 1 confirm; 0 do not confirm (Any option can be set -

command confirm is not used at the present time. it is prepared for

future appliances)

Note: Parameters in the setting SMS must be separated by commas

and blank space. Any parameter which is not required can be replaced

by a blank space. The programming sequence can be finished by

setting the last required parameter.

Examples of setting SMS:

MASTER GPRS internet

- To set the name of the access point APN to “internet”

MASTER GPRS internet, , ,1

- To set APN to “internet”, access name and password are blank,

confirmation is activated

MASTER GPRS DEL

- To delete all parameters. Connection via GPRS will not be possible.

4.6 RESET

To reset the Allegro to the factory default settings:

RESET EN

- set parameters to factory default setting (tab. 1), all texts will be in

English (tab.5 and 6)

RESET PAR

- set parameters to factory default setting (tab. 1), texts will not be

changed

RESET GSM

- to disconnect from the GSM network for a short moment. This function is

useful when it is necessary to switch the mobile device off and on (e.g.

when the SIM card has been unblocked by the mobile operator).

Jablotron GD-06 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Jablotron GD-06

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info