Bedienungsanleitung Jablotron JA-60GSM (Seite 4 von 6) (Englisch)

554884

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

User manual JA-60GSM - 4 - MFJ51808

1.10. Alarm system remote control via a telephone keypad

If you want to operate the alarm system via a phone (mobile or landline), perform the following:

 Dial the GSM dialer number. An attached telephone will ring.

 If the phone is not answered the system will answer in 25 seconds - indicated by a short beep.

 Enter the remote access code; factory default is 1111; to change this code see section 4.1.

 Confirmation sounds indicate the control panel mode: 1 beep = armed, 2 beeps = disarmed, 3 beeps

= programming mode, Siren sound = alarm.

 From this moment the telephone keypad will work as the alarm control panel keypad. Key E is

interpreted as F, key # as N.

 To terminate the connection simply hang up. Connection will automatically terminate if there is no

entry within 60 seconds.

Notes:

 Remote access from a landline is only possible from a phone using tone dialing (DTMF)

 It is impossible to operate the system remotely without a valid remote access code (if used).

1.11. Remote controlling of an appliance via a telephone keypad

If you want to operate outputs PgX or PgY (e.g. an appliance in the house) from a phone (mobile or

landline), perform the following:

a) Dial the GSM dialer number. An attached telephone will ring.

b) If the phone is not answered, the system will answer in 25 seconds - indicated by a short

beep.

c) Enter the remote user access code; factory default setting is 1111; to change this code see

section 4.1.

d) The system will confirm the validity of the code with a beep.

e) From this moment you can operate the PgX and PgY outputs by entering:

80 - to switch off

 81 - to switch on (permanently)

f) To terminate the connection simply hang up. Connection will automatically terminate if there

is no entry within 60 seconds.

Notes:

 Remote access from a land line is only possible from a phone using tone dialing (DTMF)

 If the system is programmed to allow control only with a valid code the control sequence must

be complete with a user code: (∗8[code]0 or ∗8[code]1).

 For using this function the alarm system must support F 81 and F 80 sequences

1.12. Remote voice communication with premises

If the SP-01 intercom is plug-in to the PHONE terminal (it must not be combined with any phone

connected) it is possible to create a one way (talking or listening) communication from an authorized

(stored) phone numbers (see 2.1.). Procedure:

a) From an authorized phone dial the JA-60GSM phone number. The SP-01 will ring once and

then it will answer the call

b) Potential alarm on the control panel will be terminated

c) You can talk to the premises

d) For switching to the listening mode press 5 on your phone. For switching back to the talking

mode press key 2. Or by pressing button 1 it is possible to toggle between talking and

listening.

e) Press 0 or hang-up to terminate the call.

Note:

 Only a phone with available DTMF can be used.

User manual JA-60GSM - 9 - MFJ51808

4. General settings

Enter the user mode (see section2.) before using any of the following sequences.

4.1. Remote access code

9 4 xxxxxxxx F1

where:

xxxxxxxx is the code, it can have from 1 to 8 digits

If you enter 94F1 - the code is erased and the remote access to the alarm system is not allowed.

Default setting: 1111

4.2. One-time dialing-in when in user mode

While the control panel is in the user mode, you can enable one-time remote access by entering 970. After

entering this code the dialer responds to the first ring of any incoming call. The access code is not requested,

so the calling phone keypad can be immediately used as the keypad of the alarm system (* = F, # = N).

The immediate dialing-in will be disabled after you dial-in or after you exit the programming mode.

4.3. GSM signal monitoring

The proper function of the GSM dialer is conditional on the GSM signal being strong enough. Enter

971 to measure the GSM signal level. The keypad’s display shows a number from 0 to 9 and it beeps

every second indicating a new measurement. For proper functioning of the module the signal level

should be 3 or higher. Find the best location for the antenna while measuring the signal level.

To switch the system back to the user mode press the N key.

4.4. Attached phone function

The dialer provides a PHONE output to connect an ordinary telephone set. The function of this

telephone can be modified by entering:

98 y

where function

y = 0

ordinary telephone line is simulated, it is possible to

make phone calls (indicated by a dial tone in the

receiver)

y = 1

if you pick up the receiver, the telephone keypad will

work as the keypad of the alarm system. It is impossible

to make phone calls in this mode (you will hear sounds

of the alarm keypad in the receiver)

y = 2

disabled - the telephone has no function

y = 3

emergency call – if you pick-up the phone, it will dial the

emergency number (see section 4.5)

Notes:

 It is possible to switch from mode 0 (ordinary telephone line simulation) to mode 1 (alarm

system keypad) by pressing the “#” key (handset must be picked-up). The phone will return

to mode 0 after being hung-up.

 In mode 3 (emergency call) it is possible (within 2 seconds after picking the handset up) to

switch to mode 0 (ordinary telephone line simulation) or mode 1 (alarm system keypad) by

pressing the “ *” or ” #“ key.

4.5. Emergency call number setting

If the attached telephone is programmed for emergency calls (see section 4.4), it will dial the

emergency number after the handset is picked up.

Jablotron JA-60GSM Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Jablotron JA-60GSM

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info