Bedienungsanleitung Jablotron JA-80K (Seite 19 von 22) (Englisch)

554835

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

Installation manual: Oasis security system JA-80K - 19 - MKE51801

B in an unsplit system: hot key for setting sections A and

B (e.g. partial night-setting of the garage and the ground

floor).

in a split system: hot key for setting section B (C is only

set if both sections A and B are set)

? Display of triggered detectors (e.g. open windows), fault

details and PGX / PGY status.

turning on the PGX output from the keypad (the same

effect as ∗81)

turning off the PGX output from the keypad (the same

effect as ∗80)

Notes:

• The A and B keys only have a function if partial setting or

splitting are enabled.

• The keys

and only control the PGX output if they have

been programmed for it, see 12.5.

13.1.5. Functions beginning with the ∗ key

The following functions are available to the user via the

keypad:

∗1 sets the entire system (the same as key ABC)*

∗2 sets section A (the same as key A)*

∗3 sets A and B, or just B (the same as key B)*

∗4 event memory recall (key 4 scrolls backwards) – the

control panel records max. 255 of the latest events

∗5 new Master Code/Card (∗5 MC NC NC)

∗6 access code/card programming (∗6 MC nn NC)

∗7 for operation while under duress (should be entered

before the access code to secretly signal distress)

∗8 PGX control (ON/OFF = ∗81/∗80 or enter ∗8 to trigger if a

pulsed switching reaction is programmed)*

∗9 PGY control (ON/OFF = ∗91/∗90 or enter ∗9 to trigger if a

pulsed switching reaction is programmed)*

∗0 To enter Service Mode (∗0 SC – factory default 8080) or

to enter maintenance mode (∗0 MC – factory default

1234)

The ∗ functions allow the system to be operated from a mobile phone

keypad (if the control panel is equipped with the relevant

communicator).

13.2. Programming access codes and cards

The system can be controlled by 4-digit codes or by access

cards, of the types PC-01 and PC-02 (EM UNIQUE 125kHz

standard).

• The control panel has 1 service, 1 master and 50 user codes.

• Only a numerical code can be used as a service code (factory

default 8080) – see the control panel programming section.

• The master code can be a numerical code (factory default

1234) or an access card. Using this master code/card, other

users’ codes and cards can be programmed or erased. The

master code/card is usually used by the system administrator.

• Each user from 01 to 50 can have a numerical code, or a

card, or both (factory default: all user codes and cards from 01

to 50 are erased).

• If a user has both a code and a card, then it is possible to

program whether both a code and card must be presented to

the system for system access, or whether only one of them is

required (see 12.37).

• The system does not allow the same code or card to be

programmed to multiple users. (if it is desired to move a

code/card to another user, the card/code has to be erased

from its current user first).

• It is possible to display which code/card positions are already

occupied in maintenance mode (see 13.4.1).

• The most convenient way to program codes and cards is by

using a PC running Comlink software.

• The control panel allows a maximum of 10 unsuccessful

attempts in a row to enter a valid code or card. If exceeded, a

tamper alarm starts.

13.2.1. Programming access codes and cards

Abbreviation Name Number Sequence Notes

SC Service

5 NC NC

• Only programmable in Service Mode.

• NC = new code (must be entered twice) – a card cannot be used.

• Factory-default service code: 8080

• This code can be changed but not erased.

• Example: 5 4567 4567

MC Master

∗5 MC NC NC

• Only programmable if the system is totally unset (disarmed)

• MC = master code or card (factory default 1234)

• NC = new code or card entry – a numerical code has to be entered twice, but a

card only presented once

• Either a code or a card can be programmed as a master code (to have both is

impossible).

• The Master Code can be changed but not erased.

• The Master Code’s reaction is set/unset and it is assigned to all sections.

• To reset the Master Code to the factory default 1234, enter 291 in Service Mode

(this will only affect the Master Code).

• To make handing over the system to the end user easier, we recommend

programming the system card (provided with the control panel) to the master

code.

• Example:

∗

5 1234 and then presenting the card to the keypad’s RFID reader

UC User

∗6 MC nn NC

• Only programmable if the system is totally unset

• MC = Master Code or card.

• nn = user code or card position from 01 to 50.

• NC = new code or card entry.

• Factory default: all user codes and cards are erased.

• Each user position can have both a card and a code programmed to it (by using

the sequence ∗6 MC nn NC twice)

• Each user code can have its own reaction programmed by an installer in Service

Mode, and with a split system, codes can be assigned to different sections.

• Example:

∗

6 1234 12 4345 (code 4345 will be programmed to user position 12)

To erase codes/cards enter:

∗6 MC nn 0000 erases the code and the card in user position nn.

∗6 MC 00 UC erases the code UC (or card UC) if programmed to any user position.

∗6 MC 00 0000 erases all user codes and cards in user positions 01 to 50.

Jablotron JA-80K Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Jablotron JA-80K

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info