Bedienungsanleitung Jablotron JA-80K (Seite 20 von 22) (Englisch)

554835

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

Installation manual: Oasis security system JA-80K - 20 - MKE51801

13.3. Setting and unsetting (arming/disarming) the

system

The system can be set and unset from a keypad, a keyfob or

remotely by phone or the Internet or from a PC running Comlink

software.

To set the system from a keypad:

• Press key ABC, A or B,

• Enter a code (or present a card)

• If the system is partially set (section A is set), and you wish

to extend the proportion of the system which is set, press

the B or ABC key. If you extend the proportion of the system

which is set, then all delayed or next-delayed detectors in

the section(s) going to be set and in the section currently

set, will provide an exit delay which means that if a user has

his system partially set (e.g. night setting) and wishes to exit

the house by walking through the sections that are still set,

he will not need to unset the whole system before leaving

the house and setting the whole system. The route used by

the user to leave the house must be covered by delayed or

next-delayed detectors to make this possible and must be

considered at the system design stage.

To unset the system from a keypad:

• Enter a valid access code (or present a card).

Operating the system from an outdoor keypad

If the system is equipped with a JA-80H outdoor keypad or a JA-

80N external card reader then the outdoor device could either

work the same way as an indoor keypad unit or it could be

programmed only to operate an electric door lock (known as an

outdoor-bypass feature), i.e. an indoor keypad would then be

used to control the alarm system. If the outdoor-bypass feature

is enabled then:

• Setting and unsetting the alarm system is only possible

using a JA-80F or JA-80E indoor keypad or a keyfob.

• Entering a valid access code or presenting a valid card to

the outdoor keypad or card reader will always only open the

electric door lock.

• If the system is set, and the door is opened via the outdoor

keypad or reader, an entrance delay will begin. During this

delay the system has to be unset using an indoor keypad

unit (or keyfob).

13.4. Maintenance Mode

Maintenance mode can be entered using a master code or

master card by entering:

∗0 MC

where MC = master code (card) – factory default 1234

In maintenance mode it is possible to:

• Test devices (an alarm cannot be triggered),

• Display which code/card positions are currently occupied

• Bypass individual devices (for one setting/unsetting cycle or

indefinitely) - see 13.4.2.

• Program the real-time system clock – see 12.46.

• Program the automatic setting/unsetting schedule – see

12.43.

• Program telephone numbers for event reports to the end user

(see 12.6).

• Exit maintenance mode by pressing the # key.

13.4.1. Displaying which user/card positions are occupied

Which positions in the range 01 to 50 are occupied by codes or

cards can be displayed in maintenance mode as follows:

1. The control panel must be in maintenance mode – if not then

enter ∗0 master code or card (factory default: 1234) while the

system is totally unset.

2. Press key 5 (the display indicates “Codes 01: Code”),

3. Using the arrow keys all user positions (01 to 50) can be

scrolled through, with the A indicator showing whether a code

is programmed or not, and the B indicator showing whether a

card is programmed or not.

4. To exit this code/card display mode press the # key.

5. To exit maintenance mode press the # key.

To change access codes and cards use sequence ∗6 MC nn NC

(see 13.2).

The most convenient way to administer codes is by using a PC

running Comlink software.

13.4.2. Bypassing devices

In maintenance mode it is possible to bypass (disable) individual

system devices (permanently or only for one setting/unsetting

cycle):

1. The control panel must be in maintenance mode – if it is not,

then enter ∗0 master code (factory default: 1234) while the

system is totally unset.

2. Press key 1, to display the control panel’s bypass menu.

3. Using the arrow keys you can scroll through all the devices

able to trigger alarms.

4. To bypass a device use key:

2 to bypass the device for one setting/unsetting cycle (the

triangular indicator will start flashing)

3 to permanently bypass a device (the triangular indicator

will light continuously)

To cancel the bypassing of a device use the same button

as was originally used for bypassing (2 or 3). Using key 4

will cancel all device bypasses in the system.

5. All the desired bypasses can be programmed by

repeating step 3 and 4.

6. Press the # key to exit the bypass menu. Pressing #

again exits maintenance mode.

If a system with bypasses programmed is being set, then bypass

text will be displayed on the keypad unit.

13.4.3. Protecting a car near the system

The Oasis system can also protect a car (cars) parked in the

proximity of the house.

1. If the car has a built-in car alarm then an RC-85 transmitter

unit can be connected to the car alarm output and the

transmitter unit can be enrolled to a free address in the Oasis

control panel. An alarm triggered in the car can be indicated

as an Oasis panic alarm 24 hours a day whether the system is

set or not. Note: if the car alarm confirms setting (arming) by

siren chirps appearing on the alarm output, then these should

be disabled to avoid false alarms.

2. If the car has no built-in car alarm then JA-85P or JA-85B

detectors can be installed in the car. The car detectors can be

assigned to their own dedicated section in the system, e.g. a

split system where section A could be for the car detectors,

and section B for the house detectors, with no detectors

assigned to section C, and the entry codes/cards assigned to

section C to access the whole system. So when the user

enters the house he can set section A to protect the car, and

unset section B to be able to enter the house. Radio

communication supervision should be disabled for the car

detectors to avoid fault notifications when the car is driven

away from the house.

Jablotron JA-80K Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Jablotron JA-80K

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info