Bedienungsanleitung Jablotron JA-82Y (Seite 5 von 13) (Englisch)

555059

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

The JA-82Y GSM communicator installers manual 5/5 MDL51108

Example: by sending SMS 8080_PRG_∗08080_201_# the exit delay will be set

to 10s

6.23. Registration code

You need to know the communicator registration code when first connecting via

the OLink software through the Internet. The code is stated on the label on the

communicator panel but it can also be sent to the mobile phone by SMS. To

request a registration code, enter:

911 xx...x∗0

where xx...x is the number of the phone where the code should be sent

Notes:

• The time needed for delivery of the code depends on the current GSM network

speed

• Each communicator has a unique registration code in the following format:

xxxxx-xxxxx-xxxx

6.24. Remote access password

This security key for data communication is a condition for remote access to the

system via OLink program. It is set through the following sequence:

894 xxx …x ∗0

where:

xxx…x is a security access password which can have 1 to 32 digits

Note: If a password using letters is required, it must be set in the OLink software or

by an SMS message. Letters are case-sensitive.

Factory default setting: 1234ABCD

6.25. Restarting GSM communication

After 893 has been entered, the communicator disconnects from the GSM network

and then re-registers itself. This re-registration does not change any settings in the

communicator. It should be used after GSM network faults or data collisions and in

some networks it also has to be used after a blocked SIM card has been

unblocked by the GSM provider. It is also possible (if the SIM card can still receive)

to trigger GSM network re-registration by sending the SMS instruction:

code GSM

6.26. Communicator reset

Entering 998080 returns the communicator to its factory default settings.

Telephone numbers will be erased together with all untransmitted reports but the

text settings in the communicator will not be changed.

6.27. SIM card’s PIN code

It is recommended to use a SIM card with disabled PIN protection in the

communicator. If you still want to use a card with PIN protection, enter the PIN by

entering the following sequence (it must be entered after the control panel has

been powered up):

920 PIN∗0

Example: If the SIM card PIN code is 1234, enter 9201234∗0

Notes:

• If the communicator does not register to the GSM network within 1 minute of

the PIN being entered (this problem is shown by the red LED flashing), then

you either entered a wrong PIN or the GSM signal is too weak. In such a case:

• enter 920*0 while in control panel service mode (erases the PIN entered in the

communicator)

• disconnect the control panel power (mains and battery)

• take out the SIM card, insert it into a mobile phone and check whether the PIN

is correct. Check whether the signal strength at the location of the control panel

is sufficient

• if you know the right PIN code and the GSM signal is strong enough, put the

SIM card back into the communicator, turn on the control panel power and then

enter the correct PIN code (920 PIN *0) and wait until the communicator

registers to the GSM network (its red LED should turn off within a minute)

• The communicator memorizes the set PIN and it will use it automatically

whenever it registers to the GSM network again.

• If you are replacing the SIM card in the communicator with another one and the

former one used a PIN code, first switch the control panel to service mode and

enter 920*0 to erase the former PIN code. The SIM card can then be changed.

Warning: The PIN code cannot be changed if the ARC settings are locked

Factory default setting: The PIN code is erased

6.28. GPRS parameter setting

GPRS data communication (wireless Internet via a GSM network) is used for

remote access via the OLink software and also for communication between the

system and the ARC. To use GPRS data communication it must first be enabled

(activated) in the SIM card (contact your GSM provider for details). Depending on

the SIM card used, the GPRS parameters (APN and possibly the login and

password if the SIM card requires them) must be programmed by sending the

following SMS instruction to the communicator.

code_GPRS_ x..x_y..y_z..z

where:

Code valid service system code (e.g. 8080 )

_ space

x..x SIM card APN

y..y username (do not enter if not required)

z..z password (do not enter if not required)

Examples:

For a T-mobile Czechia card enter: code GPRS internet.t-mobile.cz

Warning: The GPRS parameters cannot be changed if the ARC settings are

locked

Factory default setting: APN = internet

7. Communication to the ARC

7.1. ARC phone numbers

Events can be reported to up to 2 ARCs (which can be independent or ARC2 can

work as ARC1’s backup). Each ARC can have its main and backup phone

numbers (or IP addresses) programmed with:

Main: 01 p xx....x∗0

Backup: 02 p xx....x∗0

where:

p 1=ARC1, 2=ARC2

xxx...x tel. number (max.20 digits) or IP address and port – entry format

example.: 01 2 ∗8 192 168 001 123 08080 ∗0

where: ∗8 (auto-converts to #) signifies an IP address which must have 12

digits and must be followed by the 5 digits of the port number (no

separators).

To erase a tel. number / IP address enter 01p∗0 or 02p∗0. If

numbers / IP addresses are erased there will be no reporting to that

particular ARC.

Notes:

• the communicator first tries to send data to the main number / address, if it

is not successful it tries the backup number / address.

• the ARC address can also be entered as URL (via OLink only)

Factory default setting: all tel. numbers / IP addresses erased

7.2. Installation (alarm system) ID for ARC use

The installation’s ID number which is sent to an ARC with every report can be

programmed with:

03 p zz..z∗0

where:

p 1=ARC1, 2=ARC2, 3=IMG

zz..z installation ID number, max. 8 characters (0 to 9 and *1=A to *6=F)

Factory default setting: for all ARCs = 0000

Note: If you want to transmit photographs, enter 3 in the p parameter

7.3. Selecting the ARC communication protocol

To select the required communication protocol enter:

04 p x

where:

p 1 = ARC1, 2 = ARC2

x 0..2 = ARC type

0 = Contact ID, 1 = Jablotron IP, 2 = Jablotron SMS

Notes:

• Jablotron IP is the fastest of the abovementioned protocols and it is the only

one which allows very frequent checking of communication reliability with

the ARC (e.g. every 5 minutes).

• Contact ID protocol can be directed to ARCs linked by standard telephone

lines (if they support Contact ID).

• If your ARC does not allow Jablotron SMS or Jablotron IP protocols, please

contact a Jablotron distributor for details on how to upgrade your ARC

Factory default setting: ARC1 - Jablotron IP, ARD2 - Jablotron SMS

7.4. Selection of events to report to ARCs

This sequence allows you to select which events are reported to the ARC:

05 p uu x

where:

p 1 = ARC1, 2 = ARC2

uu Event numer 00 to 97

x 0 = no report, 1 = report

Factory default setting: See the table below

Jablotron JA-82Y Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Jablotron JA-82Y

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info