Bedienungsanleitung Jablotron JA-83K (Seite 4 von 22) (Englisch)

554836

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

terminals (max. 0.5A). The IW output status is also

transmitted for the wireless IW siren.

The difference between the internal warning (IW) output function and the

external warning (EW) one lies in their behaviour during the entrance delay

period. If any instant reaction detectors are triggered during the entrance

delay period, (e.g. by a child running straight to the living room during

disarming), only an internal warning is triggered. An external warning follows

only if the entrance delay has been exceeded (but no longer than 30

seconds).

PGX, PGY a pair of programmable outputs. When activated, the outputs

switch to GND, with a maximum load of 0.1A/12V. The

factory-default setting of PGX is the ON/OFF function

(operated by the instruction 81 / 80 or using 

ON and

#OFF keys). PGY is activated if any part of the system is

armed. The status of PG outputs is also transmitted to AC

and UC wireless output modules by the control panel.

GND common ground connection

A,B E-LINE digital bus data signals. The bus output can be routed

outside the control panel box.

+L back-up power supply (10 to 14V) feeding the devices on the

E-LINE bus (e.g. a wired keypad), electronic fuse, max.

intermittent load 200 mA.

JA-83K control panel installation manual - 4 - MKG51101

3.2 Hard-wired inputs on the main board

There are hard-wired input terminals for 01-10 device addresses on the

main board. All hard-wired inputs act identically: double balanced loops which

sense loop stand-by, activation or tampering as follows:

stand-by connected to COM via a 1 kΩ resistor (terminating resistor)

activation connected to COM via a 2k to 6k resistor 

tampering connected to COM via a less than 700  resistor (short-

circuit) or connected to COM via a more than 6k resistor

(loop termination)

12 34

OFF

GND

COM

fig. 2 SA-200 magnetic detector connection

12 34

OFF

GND

COM

fig. 3 JS-20 Largo detector connection

12 34

OFF

GND

COM

fig. 4 One-loop connection of JS-25 Combo

12 34

OFF

GND

COM

fig. 5 Two-loop connection of JS-25 Combo (01 GBS, 02 PIR)

12 34

OFF

GND

COM

fig. 6 Connection of multiple detectors to the inputs – schematically

 The used input zone must be terminated by a 1k resistor in stand-by

state.

 When connecting a trigger contact to the zone, always use a parallel

1k resistor. Thus it is possible to connect up to 5 trigger contacts in

series.

 Tamper contacts should be connected in series (without resistors).

They therefore interrupt the whole loop. You can use an unlimited

amount of tamper contacts which can be combined with trigger

contacts (with parallel resistors).

 The loop (input) reaction can be set. The NATURAL = delayed loop

reaction is set in the factory.

 If you enrol a wireless device to the hard-wired input address, the

corresponding terminal will be disabled (it will not affect the system).

 If you do not intend to use the hard-wire input or enrol a wireless

device to its address, switch the corresponding switch to the OFF

position (switch off the input).

3.3 Installation of additional hard-wire input

modules

By adding the JA-82C module it is possible to extend the amount of

inputs to twenty (addresses 01-20). When only one JA-82C module is

installed (extension to twenty inputs) module position 4 must be used -

see fig. 1.

When two JA-82C modules are installed, the maximum amount of thirty

hard-wire inputs (addresses 01-30) is reached. All hard-wire inputs behave

identically: they are double balanced inputs which are able to sense stand-by,

activation and tampering and for which examples of connection and

conditions stated in Chapter 3.2 apply in full scope.

When you install the module, relabel the terminal description with a

sticker from the module package pursuant to the current position for which

the module is intended (inputs 11-20 or 21-30). Insert plastic spacing posts

on the openings in the module on the connector side and insert the prepared

module to the selected position in the main board.

3.4 Radio module installation

The JA-82R radio module is installed in position 13 (see fig. 1). The

module antenna is included in the package and it should be inserted in the

groves on the side of the side of the box (see fig. 17). The antenna

connectors are thus connected to the pins on the JA-82R module. The

module installation enables the system to enrol wireless devices.

3.5 Y,X,V communicator module installation

Screw the selected communicator onto the holder bolted in the bottom

right corner of the control panel box.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Jablotron JA-83K Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info