Bedienungsanleitung Jablotron UC-230 (Seite 1 von 2) (Englisch)

555021

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

UC-230 Remote Control Switch 1/2 MEW51204

UC-230 Remote Control Switch

Description

The UC-230 electronic switch can replace a standard mechanical wall

switch. It is directly powered from the mains (230 V AC). By pressing the

switch up or down it works as a standard mechanical switch. At the same

time a built-in receiver in the UC-230 enables reception of control signals

transmitted from RC-xx remote controls or JA-60 wireless detectors. Thus

the mains electric circuit can be switched on or off using a remote control

or automatically when a wireless detector is triggered. Different operating

modes can be used (2 minutes pulse, over switching, on/off).

Specification:

Power supply mains 230 V, 50 Hz

Switch output 25 W – 300 W

Built-in fuse F1.6 A

Coverage class IP 40

Operating temperature indoor, -10°C to +40°C

Working frequency 433.92 MHz

Working range (open area) RC-11 – max. 30 m

RC-22, RC-28, JA-60P, N – max. 100 m

Number of RC remotes or JA-60 detectors max.8

Note: If a momentary consumption is 2 A (for maximum 10 seconds)

and the permanent load doesn’t exceed 300 W, then a 2 A fuse can be

used (fluorescent lamps).

Complies with EN 60950, EN 300220, ETS 300683.

Hereby, Jablotron Ltd., declares that this UC-230 is in compliance with

the essential requirements and other relevant provisions of Directive

1999/5/EC.

Original of the conformity assessment can be found at the web page

www.jablotron.cz, section Technical support.

Installation

The UC-230 switch should be mounted as a usual wall switch.

Follow these steps:

• Switch off the power and remove the old switch

• Open the cover using a small

screw driver (see picture)

• Connect the wires to the terminals

• Attach the housing to the junction

box with screws (button A up)

• Close the cover (LED indicator

must be in the upper right corner)

• Switch on the power supply

• Test the switch manually (press

upper part to switch it on, lower part

to switch it off)

In order to use the UC-230 for controlling fluorescent lamps with

consumption bellow 25W, connect the KF-01 compensation filter in

parallel to the lamp. This filter eliminates lamp flickering when it is

switched off.

Enrolling wireless remote controls and/or detectors

To enroll remote controls and/or wireless detectors to the UC-230,

proceed with the following steps:

1. Press and hold the upper side of the UC-230 (next to the LED

indicator) for 10 seconds.

2. The red LED will flash to confirm entering the learning mode.

3. Press a button of a remote control or insert batteries to a wireless

detector. The LED will turn off confirming that the accessory has

been enrolled.

4. You can repeat steps 1 – 4 and enroll more accessories (up to 8).

Note: The enrolling mode will automatically close in 20 seconds if no

accessory has been enrolled.

Operating modes

Enrolled JA-60 wireless detectors trigger the UC-230 for 2 minutes.

If you enroll RC-11 or RC-22 remote controls they will switch on with

one button and off with the other one.

However, you can select other functions for the remote controls. In

the enrolling mode (LED flashes red) press down the lower (B) UC-230

button. The LED color will change every time you press the button.

This allows you to select other operating modes:

Green flash overswitching mode (the enrolled button will

change the switch status every time it is pressed –

on- off-on -…) – suitable for RC-11, RC-22 and

RC-28 remotes.

Yellow flash 2 minutes pulse – the button enrolled in this mode

will trigger the UC-230 switch for 2 minutes

Red flash switch mode (one button on, the other off) –

suitable for RC-11 and RC-22 remotes

Notes:

• The function of the JA-60 wireless detectors remains the same

despite the color of the LED during enrollment (2 min. pulse)

• Permament switch off - If you don't want the UC-230 to be triggered

byenrolled JA-60 detectors, switch off the UC-230 manually once

again. It means, that if red LED flashes on the UC-230, enrolled JA-

60 detectors are bypassed unitll the receiver is switched on again

(manually or by enrolled RC-xx remote control)

• Permanent switching – If you want to have the UC-230 permanently

on, switch it on once again manually. This will obstruct reception of

radio instructions until it is switched off manually by pressing the

lower button.

LED indicator

The LED indicates the following status:

Red light = off

Flashing of red LED - off (enrolled detectors are bypassed)

Green light = on (enrolled detectors are bypassed)

Yellow light = on for 2 minutes

Optional function of the UC-230

The factory default setting (upper button – on, lower button – off) can be

changed if necessary.

After opening the cover (Caution – dangerous voltage inside!) press and

hold the B button and then scroll with the A button through the following

modes:

• Green light = overswitching mode (operated by both the upper and

the lower button)

•

Yellow light = 2 minute pulse mode (operated by both the upper

and the lower button)

•

Red light = switch mode (factory setting)

Deleting the accessories

Switch the UC-230 to the enrolling mode. Then press and hold the

lower button on the UC-230 switch for 10 seconds. All enrolled items

will be deleted from the memory. LED will confirm this with short green

and red flashes.

Internet: www.jablotron.cz

Tel.: +420 483 559 999

fax: +420 483 559 993

Pod Skalkou 33

466 01 Jablonec nad Nisou

Czech Republic

Jablotron UC-230 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info