809288
4
Zoom out
Zoom in
Vorherige Seite
1/9
Nächste Seite
JBL BASSPRO GO
4
EN
IV. SETTING THE SOUND IN THE
VEHICLE
In Settings Mode, you can adjust the input level, gain, low-pass
crossover, phase control, and bass boost.
FULL RANGE MODE
CONNECT TO VEHICLE
WOOFER MODE
FULL RANGE MODE
SETTINGS MODE SETTINGS MODE SETTINGS MODE
Press & Hold JBL Connect and
Play/Pause buttons for 5s
Press & Hold JBL Connect and
Bluetooth buttons for 5s
Press JBL Connect button to
toggle menu items
INPUT SENSITIVITY
CROSS OVER
GAIN
BASS BOOST
PHASE CONTROL
Press & Hold JBL Connect and
Bluetooth buttons for 5s
Press JBL Connect button to
toggle menu items
INPUT SENSITIVITY
CROSS OVER
GAIN
BASS BOOST
PHASE CONTROL
Press & Hold JBL Connect and
Bluetooth buttons for 5s
Press JBL Connect button to
toggle menu items
INPUT SENSITIVITY
CROSS OVER
GAIN
BASS BOOST
PHASE CONTROL
NOTE: To enter Full-Range Mode from Subwoofer Mode, press and
hold the JBL Connect and Play/Pause buttons for 5 seconds. To switch
back to Subwoofer Mode, repeat the same process.
A. Entering Settings Mode
Press and hold the JBL Connect button and the Bluetooth button
for 5 seconds to enter Settings Mode. The power button will
illuminate in yellow and an alert will sound. Press the JBL Connect
button to toggle between settings. Press the “+” and “–” buttons
to change the value of each setting.
The color of the first LED indicates which setting you are adjusting.
The five white LEDs display the value of the adjustment.
Setting First LED color
Input level (docked in vehicle
only) Blue
Crossover (docked in vehicle in
woofer mode only) Red
Gain (docked in vehicle only) Green
Bass boost Orange
Phase (docked in vehicle in
woofer mode only) Teal
B. Setting the input level
When the BassPro Go is docked in your vehicle, you will need
to set the input level to accept the type of signal it receives from
your source unit. Select level options by pressing the “+” and “–”
buttons.
Signal from source unit LED configuration
LO (low-level preamp outputs)
HI1 (high-level speaker outputs)
HI2 (high-level speaker outputs
if no playback from HI1)
C. Setting the low-pass crossover in subwoofer
mode
The crossover allows only frequencies below a certain point to
reach the speaker in woofer mode. The crossover point you
choose depends on your musical preferences.
Crossover point LED configuration
80Hz
100Hz
120Hz
D. Setting the gain
When the BassPro Go is docked in your vehicle, you will need to
match the gain (input sensitivity) to output of the signal it receives
from your source unit. To set the gain:
1. Start with gain control switch set to 2V.
2. Choose music with substantial bass content and turn the
volume control on your receiver to 75% of its total output.
3. Increase the gain one step at a time by pressing the “+”
button, listening carefully to the bass output, as the LED read
out displays each step. To increase the interval of the gain you
are adjusting, move the gain control switch to 2V, 4V, or 6V as
necessary. If you hear distortion, lower the gain one step at a
time by pressing the “–” button until the distortion disappears.
Input
signal
type
Gain
control
switch
setting
Gain
level LED configuration
Line-level 2V 0.4V - 2V
Line-level 4V 0.8V – 4V
Line-level 6V 1.2V – 6V
High-level 2V 1V – 5V
High-level 4V 2V – 10V
High-level 6V 3V – 15V
JBL BassPro Go_owners manual_SOP_V6.indb 4JBL BassPro Go_owners manual_SOP_V6.indb 4 11/23/2020 5:53:00 PM11/23/2020 5:53:00 PM
4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für JBL BassPro Go wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von JBL BassPro Go

JBL BassPro Go Bedienungsanleitung - Deutsch - 9 seiten

JBL BassPro Go Bedienungsanleitung - Holländisch - 9 seiten

JBL BassPro Go Bedienungsanleitung - Französisch - 9 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info