Bedienungsanleitung JL Audio MX600 (Seite 2 von 2) (Englisch)

700477

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Problem Possible Cause Solution

How to properly set

input sensitivity



Please refer to Appendix A to set the

input sensitivity for maximum, low-

distortion output.

Amplifier doesn’t

turn on

Faulty fuse

Remove fuse and check with continuity

meter. Replace if necessary.

Poor connection

integrity

Check “+12V”, “Ground”, and “Remote”

leads for pinched wires; ensure tight

connections.

Insufficient “Remote”

input

Make sure there is a sufficient +12V

supply at the “Remote” connection; if

not a relay may be required.

Intermittent output,

fluctuates when I tap

on it or hit a bump

Poor connection

integrity

Make sure insulation has been properly

stripped back at connection points for

good contact area.

Make sure input connectors are making

good contact with input jacks of the

amplifier.

Distorted, attenuated,

or popping sound

Faulty speaker

connection (Short

Circuit / Over Current

Protection)

Inspect speaker wires for possible

short-circuit, either together or shorted

to the vehicle’s chassis ground.

Check the nominal load impedance at

the amplifier is equal to or greater than:

Ch.1 & 2: 2 ohms stereo

Ch.1 & 2: 4 ohms bridged

Sub Ch.: 2 ohms

Output shuts off after

a while

Overheating

condition (Thermal

Protection)

Make sure amplifier mounting area has

adequate space for ventilation and heat

dissipation.

No or low subwoofer

output

Remote Bass

Control (optional)

is connected and

turned down

Adjust RBC-1 or M-RBC-1 accordingly

Limited Warranty – Amplifiers (USA)

JL Audio warrants this product to be free of defects in materials and

workmanship for a period of two (2) years from the original date of purchase.

This warranty is not transferrable and applies only to the original purchaser

from an authorized JL Audio dealer. Should service be necessary under this

warranty for any reason due to manufacturing defect or malfunction, JL

Audio will (at its discretion), repair or replace the defective product with new

or remanufactured product at no charge. Damage caused by the following is

not covered under warranty: accident, misuse, abuse, product modification or

neglect, failure to follow installation instructions, unauthorized repair attempts,

misrepresentations by the seller. This warranty does not cover incidental or

consequential damages and does not cover the cost of removing or reinstalling

the unit(s). Cosmetic damage due to accident or normal wear and tear is not

covered under warranty.

Warranty is void if the product’s serial number has been removed or defaced.

Any applicable implied warranties are limited in duration to the period of the

express warranty as provided herein beginning with the date of the original

purchase at retail, and no warranties, whether express or implied, shall apply

to this product thereafter. Some states do not allow limitations on implied

warranties, therefore these exclusions may not apply to you. This warranty gives

you specific legal rights, and you may also have other rights, which vary from

state to state.

If you need service on your JL AUDIO product:

All warranty returns should be sent to JL Audio ’s Amplifier Service Facility

freight-prepaid through an authorized JL Audio dealer and must be

accompanied by proof of purchase (a copy of the original sales receipt). Direct

returns from consumers or non-authorized dealers will be refused unless

specifically authorized by JL Audio with a valid return authorization number.

Warranty expiration on products returned without proof of purchase will be

determined from the manufacturing date code. Coverage may be invalidated

as this date is previous to purchase date. Non-defective items received will

be returned freight-collect. Customer is responsible for shipping charges and

insurance in sending the product to JL Audio. Freight damage on returns is not

covered under warranty.

For Service Information in the U.S.A. please call

JL Audio Customer Service:

(95 4) 443-110 0

9:00 AM – 5:30 PM (Eastern Time Zone)

JL Audio, Inc.

10369 North Commerce Pkwy.

Miramar, FL 33025

(Do not send product for repair to this address)

International Warranties:

Products purchased outside the United States of America are covered only

by that country’s distributor and not by JL Audio, Inc.

Do not increase any “Input Sens.” setting for any amplifier channel or

channel pair in the system beyond the maximum level established during

this procedure. Doing so will result in audible distortion and possible

speaker damage.

It will be necessary to re-adjust the “Input Sens.” for the affected channels if any

equalizer boost is activated after setting the “Input Sens.” with this procedure. This

applies to any EQ boost circuit, including source unit tone controls or EQ circuits. EQ

cuts will not require re-adjustment.

Target AC Voltage - MX600/3

Nom.

Impedance

Ch.1 & 2

(Stereo)

Ch.1 & 2

(Bridged)

4Ω 17.3 28.3

2Ω 14.1 not recommended

Nom.

Impedance

Ch.3/Subwoofer

4Ω 31.6

3Ω 30.0

2Ω 28.3

Troubleshooting

Appendix A:

Input Sensitivity Level Setting

Following the directions below will allow the installer to adjust the input

sensitivity of each amplifier channel pair in just a few minutes using equipment

commonly available in installation bays.

Necessary Equipment

• Digital AC Voltmeter

• CD or file with a sine-wave test tone recorded at 0 dB reference level in the

frequency range to be amplified for that set of channels (50 Hz for subwoofer

channels, 1 kHz for a midrange application). Do not use attenuated test tones

(-10 dB, -20 dB, etc.).

The Nine-Step Procedure

1) Disconnect the speakers from the amplifier’s speaker output

connectors (you need only disconnect one speaker wire).

2) Turn off all processing (bass/treble, loudness, EQ, etc.) on the source

unit, processors (if used) and amplifier. Set the source unit’s fader

control to center position and its subwoofer level control to

3/4 of maximum.

3) Set both “Input Voltage” switches to “Low” and turn both “Input

Sens.” controls all the way down.

4) Set the source unit volume to 3/4 of full volume. This will allow for

reasonable gain overlap with moderate clipping at full volume.

5) Using the Target AC Voltage chart (at right), determine the target

voltage for input sensitivity adjustment according to the nominal

impedance of the speaker system connected to the amplifier outputs.

6) Verify that you have disconnected the speakers before proceeding. Play

a track with an appropriate sine wave (within the frequency range to

be amplified) at 3/4 source unit volume.

7) Connect the AC voltmeter to the speaker output connectors of the

amplifier. Make sure you test the voltage at the correct connectors

(+ and –).

8) Increase the “Input Sens.” control until the target voltage is observed

with the voltmeter. Note: If excessive voltage is measured with the

control set at minimum (full counterclockwise), change the “Input

Voltage” switch setting to “High” and re-adjust.

9) Once you have adjusted the amplifier to its maximum low-distortion

output level, reconnect the speaker(s) and listen to the system. The

“Input Sens.” controls can now be adjusted downward if the amplifier

requires attenuation to achieve the desired system balance.

Specications MX600/3

Rated RMS Power @

14.4V, <1% THD+N

Main @

4 Ω

Main @

2 Ω

Main @ 4 Ω

Bridged

Sub @

4 Ω

Sub @

3 Ω

Sub @

2 Ω

75 W x 2 100 W x 2 200 W x 1 250 W x 1 300 W x 1 400 W x 1

Rated RMS Power @

12.5V, <1% THD+N

Main @

4 Ω

Main @

2 Ω

Main @ 4 Ω

Bridged

Sub @

4 Ω

Sub @

3 Ω

Sub @

2 Ω

50 W x 2 80 W x 2 160 W x 1 200 W x 1 250 W x 1 300 W x 1

Frequency Response 20 Hz - 20 kHz (+0, -1dB), 6.3 Hz - 30 kHz (+0, -3dB)

S/N Ratio, A-weighted,

20 kHz noise

bandwidth

88 dB (Referred to rated power), 68 dB (Referred to 1 W)

Damping Factor >92 / 50 Hz @ 4 Ω, >43 / 50 Hz @ 2 Ω

Input Voltage Range 250 mV - 4 V (Low) or 580 mV - 14 V (High)

Input Mode Switch 2 / 4 Channel

Front High-Pass Filter Freq. Range: 35 - 300 Hz Slope: 12 dB/Octave

Sub Low-Pass Filter Freq. Range: 40 - 400 Hz Slope: 24 dB/Octave

Infrasonic Filter Freq. Range: 20 - 40 Hz Slope: 12 dB/Octave

Sub Output Polarity 0 or 180 degrees

Bass Boost EQ 0 to +12 dB @ 43 Hz

Remote Bass Controller M-RBC-1 or RBC-1 (sold separately)

Input Operating

Voltage

11 - 15 VDC

Min Power/GND Wire 4 AWG

Fuse Rating 60A

Dimensions 9.33 in x 4.50 in x 1.77 in / 237 mm x 114.5 mm x 45 mm

Status LED’s / Protection Circuitry

There are two status indicator lights on the wiring end panel of the amplifier.

1. “POWER” (Green): Lights to indicate that the amplifier is turned on and

operating normally.

2. “PROTECT” (Red): Lights to indicate the amplifier’s protection circuitry

has been triggered to prevent product failure due to any conditions

noted in the chart below. When a protection mode is activated, the

amplifier will shut down to protect its circuitry. For Thermal Protection,

Over Current and Short Circuit conditions, the amplifier will resume

normal operation once the problem is corrected, with the “Protect” LED

turning off. For Over Voltage conditions, the amplifier must be turned

off/on to return to normal operation. Note: connecting the speaker

outputs to impedances lower than 2 ohms (4 ohms bridged) will also

cause this protection mode to activate.

POWER

(Green LED)

PROTECT

(Red LED)

Status/Condition Note

ON OFF Normal Operation



OFF ON Thermal Protection Lasts until temp cools to normal

OFF/ON ON/OFF Over Current Green/Red LEDs alternate for 1 second

OFF ON Short Circuit Possible audible “popping” noise

OFF ON Over Voltage Turn amp off/on to restart

Appendix B

Remote Bass Control

With the optional RBC-1 or M-RBC-1 Remote Bass Control (each sold separately),

you can control the subwoofer volume from the front of the vehicle/vessel.

The remote’s plug connects to the amplifier’s harness-mounted RJ11 input

jack. When connected to the amplifier, the Remote Bass Control operates as

follows. At full counter-clockwise rotation, the audio will mute completely. At full

clockwise rotation the level will be the same as if the remote was not connected

at all. In other words, it operates strictly as a subwoofer level attenuator. This

control will not affect the “Bass Boost” feature of the amplifier. Care should

be taken to securely mount this control in a manner that does not interfere

with vehicle/vessel operation. When setting the amplifier’s input sensitivity,

the Remote Bass Control should be unplugged or at full clockwise rotation

(maximum level).

JL Audio MX600 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info