Bedienungsanleitung Katadyn Hiker Pro Water Microfilter (Seite 5 von 8) (Englisch)

522398

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

For use without the weight. The prefilter is functional with or without the weight (we rec-

ommend using with the weight). To use without the weight, remove the strainer barb from

the input hose. Re-assemble without the weight.

4. Storage: Your Katadyn water system comes with a carry bag for storage. To prevent the

possibility of cross contamination, remove the output hose and EasyFill Bottle Adaptor and

store separately in a re-sealable bag inside the carry bag.

LONG-TERM STORAGE (AFTER YOUR TRIP IS OVER)

Disinfect your microfilter before storage to prevent microbiological growth within the pump.

1. Fill a liter container with tap water and add 2 tablets of Micropur Forte DCCNa or

Micropur MP1. (Do not use Micropur Classic.)

2. Place prefilter into solution.

3. Pump entire amount of solution through unit (into sink or container).

4. Remove prefilter from the solution and continue pumping another 5 to 10 strokes to remove

remaining water from the pump body and hoses.

5. Remove cartridge and allow to dry.

6. Wrap hoses around body and store in carry bag.

Note: When removing unit from long-term storage, flush the system with one liter of water to

remove any stale tasting water.

CARTRIDGE CAPACITY

Cartridge capacity depends on water quality. The Katadyn Hiker Pro was tested at 750 liters

(without filter protector) and found effective for removal of bacteria (Klebsiella terrigena) and pro-

tozoan cysts (Giardia and Cryptosporidium). For maximum performance, cartridge should be

replaced after 750 liters or when the unit becomes hard to pump.

CARTRIDGE INSTALLATION

Replacement cartridges are available from the dealer where you purchased your Hiker Pro.

1. Remove output hose from cartridge output barb. Grasp the top of the Hiker Pro cartridge

and turn counter clockwise. If cartridge removal is not possible by hand, the handle shaft

will function as a cartridge removal tool:

Remove the handle collar and handle. Locate one of the deep grooves on either side of the

handle shaft. Lay the handle across the filter top and insert two of the “fins” on top of the

filter into one of the groves of the handle shaft. Hold the handle shaft in place firmly with

the palm of your hand. Using the handle shaft for leverage, apply even pressure and grad-

ually turn the cartridge counter clockwise. Use caution so that handle shaft does not slip and

cause damage. Discard used cartridge in trash receptacle.

2. Rinse inside of housing by swishing with clear water (non-filtered water is ok). Discard water.

Wipe inside of housing and housing threads with soft cloth to remove sediment.

3. Remove new cartridge from packaging.

4. Insert new cartridge into housing and tighten clockwise. Note - Apply silicone lubricant to

cartridge o-ring before re-assembly to ease cartridge removal in the future.

5. Re-attach output hose to cartridge output barb. (Figure 1-1)

6. Flush cartridge by pumping and discarding the first liter.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Katadyn Hiker Pro Water Microfilter Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Katadyn Hiker Pro Water Microfilter

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info