686376
27
Zoom out
Zoom in
Vorherige Seite
1/32
Nächste Seite
27
A3 MIG Welder© Kemppi Oy 2018 1826
OPERATING MANUAL
5.2 Error codes
Code Description Measures
2 UNDERVOLTAGE
Undervoltage in the mains supply (phase missing)
Check the fuses.
3 OVERVOLTAGE
Lengthy overvoltage in the mains supply.
4 OVERHEAT
The overheat detector of the power source has gone o during welding.
Welding has continued for too long without interruption or the ambient
temperature is too high.
Do not switch o the power source. Let the fans cool down the device.
101 NO WELDING PROGRAM
Internal program error. The selected synergic welding curve was not found in
the memory. The system memory card is detached or defective.
Switch o and restart the power source. Contact the maintenance service if the
error is not resolved.
131 FIELDBUS INIT FAILED
Failed to initialize the eldbus during start-up.
Restart the device. Contact the maintenance service if the error is not resolved.
132 ROBOT COMMUNICATION ERROR
Communication to the robot has been lost. The eldbus cable has been
broken or detached, or there is a robot failure or shutdown. Welding is
interrupted when a lost connection is detected.
Check the eldbus cable. If the robot has been shut down, turn the robot on.
Switch o and restart the power source.
133 SAFETY STOP
The safety stop signal is activated by a user. Welding is immediately
interrupted.
Identify the reason for the safety stop. Do not release the safety stop signal before
the cause has been identied and resolved.
146 COLLISION DETECTED
The collision sensor has been activated. The welding torch mounted on
the arm of a welding robot has collided with the welding piece or another
obstacle.
Reverse the robot arm until the torch no longer touches the obstacle. Check the
torch in case of damages.
154 WIRE FEED MOTOR OVERCURRENT
Current limit is exceeded while the wire feed motor is running, and the motor
is stopped. The wire feeder rolls are too tight, the wire spool is too tight, or
the wire is stuck.
Check and replace the consumables in the wire feeder unit and the torch.
202 CURVE NOT ACTIVATED
An activated memory channel has not been congured properly.
Specify a welding curve for the memory channel.
### OTHER ERROR CODES Switch o and restart the power source. Contact the maintenance service if the
error is not resolved.
27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Kemppi A3 MIG Power Source 400 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info