686376
28
Zoom out
Zoom in
Vorherige Seite
1/32
Nächste Seite
28
A3 MIG Welder© Kemppi Oy 2018 1826
OPERATING MANUAL
6. OPERATION DISTURBANCES
Should you experience a malfunction from your machine,
please consult the basic troubleshooting text above rst,
and complete some basic checks.
If the machine malfunction cannot be corrected with
these measures, contact your Kemppi maintenance ser-
vice workshop.
Operation of the overload protection
Yellow thermal protection lamp is lit when the thermo-
stat is operating, due to loading beyond the stated duty
cycle.
The thermostat will operate, if machine is continuously
loaded over rated values or cooling air circulation is
blocked.
Internal fans will cool the machine, and when the pilot
lamp is not lit the machine is automatically ready for
welding.
Control fuses
Fuse, 6.3 A delayed, on the rear wall of the machine pro-
vides protection for auxiliary devices.
Use the same type and rating of fuse as marked beside
the fuse adapter. Damage caused by incorrect fuse selec-
tion is not covered by the guarantee.
Under- and overvoltage in the mains supply
Primary circuits of the machine are protected against
sudden, transient overvoltage. The machine is designed
to withstand 3 x 440 V voltage continuously. Ensure that
voltage is kept within this permissible limit, especially
when the mains supply is provided by a combustion en-
gine generator. If the mains have undervoltage (under
approx. 300 V) or overvoltage (over approx. 480 V) ma-
chine control stops operation automatically.
Loss of a phase in the mains supply
Loss of a mains power phase causes noticeably poor
welding properties. In some cases, the machine won’t
start at all. Loss of a phase can be due to following:
Blowing of mains supply fuse
Defective mains cable
Bad connection of mains power cable on
machine terminal block or plug of machine.
28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Kemppi A3 MIG Power Source 400 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info