If you also have a compatible KENWOOD handy transceiver, you may use it as a remote control for this mobile transceiver. You will
control one band on the mobile while sending DTMF tones to the other band from the handheld. This function is useful, for example,
when you want to control the mobile from a location outside your vehicle.
Note:
◆As a remote control, you can also use a handy transceiver which does not have a remote control function but a DTMF function. However, you must manually send
DTMF tones for control code strings. Skip steps 1 and 3 in “PREPARATION”.
◆The FCC rules permit you to send control codes only on the 440 MHz band.
PREPARATION
Let us assume band A (VHF) of the mobile transceiver will be
controlled.
On the handy transceiver:
1Program a 3-digit secret number.
• For the programming method, see the instruction manual for the
handheld.
2Select the transmit frequency on the UHF band.
3Make the handheld enter Remote Control mode.
• For the method, see the instruction manual for the handheld. If
not described, consult your dealer.
On the mobile transceiver:
4Enter Menu mode and access Menu 923.
5Set the ID code to the same secret number you set on the
handy transceiver.
6Select the receive frequency on band B (UHF).
• Match this frequency with the transmit frequency on the
handheld.
7Select band A (VHF) as the TX band or Control band.
8To cause the mobile to send a control acknowledgment to the
handheld, enter Menu 924 and set it to ON.
• DTMF tones which represent the secret number will be used as
an acknowledgment.
9Turn the transceiver power OFF.
10 Press [REV] + Power ON to enter Remote Control mode.
• The (blink) and icons appear on the display.
• To exit Remote Control operation, turn the transceiver power
OFF, then press [REV] + Power ON again.
CONTROL OPERATION
While in Remote Control mode, the DTMF keys of the handheld
will function as shown in the table below. Each time you press
the desired key, the handheld will automatically enter transmit
mode and send the corresponding command to the mobile.
Note: If using a handheld without a remote control function, manually send
“AXXX#YA#” where “XXX” is a 3-digit secret number and “Y” is a single-digit
control command. If you do not add ”A#” to the end, you can skip sending
“AXXX#” next time; however, the mobile may be accidentally controlled by other
Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.
Art des Missbrauchs:
Forenregeln
Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:
Lesen Sie zuerst die Anleitung;
Schauen Sie nach, ob die Frage bereits gestellt wurde;
Stellen Sie die Frage so deutlich wie nur einigermaßen möglich;
Erwähnen Sie was Sie bereits versucht haben um das Problem zu lösen;
Ist Ihr Problem von einem Besucher gelöst dann lassen Sie ihn / sie wissen in diesem Forum;
Falls Sie reagieren möchten, so verwenden Sie bitte das Antworten- Formular;
Da ihre Frage für alle Besucher sichtbar ist, sollten Sie lieber keine persönliche Daten erwähnen.
Neu registrieren
Registrieren auf E - Mails für Kenwood TM-D710GA wenn:
neue Frage gestellt werden
neue Handbücher vorhanden sind
Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.
Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.
Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.
Ihre Frage wurde zu diesem Forum hinzugefügt
Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.