159529
58
Zoom out
Zoom in
Vorherige Seite
1/64
Nächste Seite
58
Knowledge section
In case of difficulty
In case of difficulty
What seems to be a malfunction is not always so. Before calling for service, check the following table
according to the symptom of your trouble.
Unplug the power cord from the power outlet
then, while holding the ENTER key depressed,
plug the power cord again.
÷ Please note that resetting the microcomputer clears
the stored contents and returns to the factory set
condition.
Operation to reset
The microcomputer may fall into malfunction (impos-
sibility to operate, erroneous display, etc.) when the
power cord is unplugged while power is ON or due to
an external factor. In this case, execute the following
procedure to reset the microcomputer and return it to
normal condition.
Sound is not produced.
“STANDBY” and “TIMER”
indicators blink alternately
and no sound is output.
Sound is not produced from
the left or right speakers.
“Dolby pro logic” and “Dolby
3 stereo” cannot be selected.
The clock display blinks.
Timer operation is not pos-
sible.
Radio stations cannot be re-
ceived.
Sound from the DVD/VIDEO IN-
PUT (external input) is distorted.
÷ The speaker cords are disconnected.
÷ The MUTE switch of remote control
unit is switched ON.
÷ The headphone plug is inserted into
the jack.
÷ The speaker cords are short-circuited.
÷ The speaker cords are disconnected.
÷ The left and right volumes are not
balanced.
÷ The center speaker and surround
speakers are set to “No”.
÷ There was a power failure.
÷ The power cord was unplugged from
the outlet.
÷ The present time has not been ad-
justed or there was a power failure.
÷ The timer program or the timer ON/
OFF time has not been set properly.
÷ The antennas have not been con-
nected.
÷ A proper broadcasting band has not
been selected.
÷ The frequency of the station to be
received is not tuned.
÷ The input level is too high.
÷ Connect properly referring to “Sys-
tem connection”.
÷ Switch MUTE OFF.
÷ Unplug the headphone plug.
÷ Turn the power OFF, remove the short-
circuit and turn the power ON again.
÷ Connect properly referring to “Sys-
tem connection”.
÷ Adjust the left and right volume bal-
ance.
÷
Perform the center speaker and surround
speaker setting operations properly.
÷ Adjust the present time again.
÷ Adjust the present time again.
÷ Adjust the present time referring to
“Clock adjustment”.
÷ Check the timer program and set its ON/
OFF time properly. Note that “Everyday”
and “One Time” cannot be set simulta-
neously for a single timer program.
÷ Connect antennas.
÷ Select a band.
÷ Tune to the frequency of the desired
station.
÷ Decrease the input level.
Remedy
Receiver, speakers
CauseSymptom
7
(
*
7
r
i
^
^
^
R
5
§
§
t
(Main unit only)
ENTER
6
6
58

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Kenwood xd 803 8 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info