598787
4
Zoom out
Zoom in
Vorherige Seite
1/48
Nächste Seite
18. Hold power tool by insulated gripping surfaces, when performing an
operation where the cutting accessory may contact hidden wiring or its own
cord. Cutting accessory contacting a “live” wire may make exposed metal
parts of the power tool “live” and could give the operator an electric shock.
Operating the machine
Wrong use may result in damages. Therefore, the following instructions shall
always be observed:
Use stirrers recommended by the manufacturer (maximum diameter: 140 mm
(UT1401), 180 mm (UT1600) with M14 thread).
Do not overload the machine in a way that causes a standstill.
Tool change
Caution!
Do always remove the power plug before carrying out any work on the tool.
You may catch your fingers when inserting the tool. Therefore, do always wear
protective gloves when changing tools.
The work spindle of the tool is provided with a M14 internal thread.
Keep thread and front surfaces clean. Do use a SW 22 (UT 1401) or SW 27 (UT
1600) spanner to remove the stirrer and to hold up the work spindle.
Switching the machine on and off
Short-Time Operation
Starting the machine: Press on/off switch
Stopping the machine: Release on/off switch
Permanent Operation
Starting the machine: Press on/off switch and while keeping it pressed, engage
the lock button
Stopping the machine: Press on/off switch again and release it
The mixer has an electronic switch in order to regulate the speed level by
keystrokes.
It is recommended to only use it when the machine is started or stopped in order
to avoid splashing material. If the continuous mode is operated with reduced
speed, it leads to overstress because the machine is not provided with enough
cooling air and overheating will occur significantly faster.
Speed Selection
The machine is equipped with a mechanical two-speed gearbox. Select the
required speed by rotate the gear selector. The position of the lower speed is in
direction of the working spindle. Change the speed only when the machine is not
running, and support the speed-changing by slightly rotating the work spindle.
4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Makita UT 1600 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info