Bedienungsanleitung Marantec Command 231 (Seite 1 von 2) (Englisch)

742654

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Command 231

Radio code keypad for impulse control

Version

Command 231 868 MHz (Art.-No. 68 328)

Command 231 433 MHz (Art.-No. 68 333)

Safety advice

Attention:

• Please read these instructions carefully

before connecting and operating this

device!

• Have faulty and defective devices checked

by the manufacturer.

• You are not authorized to carry out

changes to this device.

Function

The radio code keypad offers you the possibility to

open and close your garage door by entering a

4-digit personal identification number (PIN). It can

be programmed, so that up to 3 garage door

operators can be actuated with a different code

each or one garage door operator can be actuated

with up to three different PIN's. Additionally any

number can be programmed temporarily as PIN in

order to grant a temporary access for certain visitors

or service personnel.

Beside this an additional device (e.g. the yard light)

can be controlled. For this function ("light function")

a further receiver is required.

Installation of the radio code keypad

• Choose a suitable place to install the radio code

keypad.

• Take the wall bracket as pattern and mark the

place for the two drill holes. Then drill the holes

and insert the enclosed wall plugs.

• Screw on the wall bracket by means of the

enclosed screws. For surfaces other than wood

other screws and wall plugs may be necessary.

• Click the radio code keypad into the wall bracket.

• Take a coin to turn the lock on the bottom side of

the wall bracket clockwise to fix the radio code

keypad.

Enter PIN and transmit code

Your radio code keypad is delivered with

1 random code and 1 PIN already programmed.

The factory programmed PIN is 1-2-3-4.

Attention:

To program the third code the preset

code (random programming) must be

overwritten with the PIN 1-2-3-4 and

then the PIN 1-2-3-4 must be changed

according to the instructions.

In case you already use another radio transmitter to

control your garage door operator, the code of this

has to be transmitted from the transmitter to the

actual radio code keypad.

Transmit the code for the garage door control

from one transmitter to the radio code keypad:

• Connect the radio code keypad and the actual

transmitter by means of the programming plug.

• Hold the button on the transmitter you control

the garage door with.

Press the ENTER button on the radio code keypad.

The keypad lights up.

• Enter a new 4-digit PIN of your choice. Then press

the ENTER button again. Hold the transmitter

button until the LED on the radio code keypad

flashes quickly.

• Now the radio code keypad has learned the

transmitter code and saved under the PIN you

have entered. Now you may remove the

programming plug.

Transmit the code for light function from one

transmitter to the radio code keypad:

The light function is already programmed with a

special code. But you may as well transmit another

transmitter code to actuate the light function.

• Connect the radio code keypad and the actual

transmitter by means of the programming plug.

• Hold the specific button on the transmitter you

activate the other device with. Press the ENTER

button on the radio code keypad. The keypad

lights up.

• Press the LIGHT button and then again the ENTER

button. Hold the transmitter button until the LED

on the radio code keypad flashes quickly.

• The radio code keypad has now learned the new

transmitter code for the light function. Now you

may remove the programming plug.

Save more than 1 code to control more than

1 garage door operator:

• With the radio code keypad you may control up

to 3 different garage door operators, each with a

different code.

• For each of the 3 codes proceed as described

above, but with one exception: You must enter a

different PIN for each code, which means each

code requires an individual PIN.

• To open or close a certain garage door with the

radio code keypad, just enter the respective PIN

and then press the ENTER button.

Save more than 1 PIN for the same code:

Beside the already programmed PIN it is possible to

save up to 2 additional PIN's for the same code and

to assign these PIN's to different persons.

• Follow the instructions described under "Transmit

the code for the garage door control from one

transmitter to the radio code keypad" for every

single PIN. Repeat these steps for each PIN with

the same transmitter. So the same code is saved

under 3 different PIN's.

Save a temporary PIN:

A temporary PIN that is valid only for three actuations

can be saved.

• Hold "button 1" for 3 sec. until the LED flashes

quickly. Enter the currently valid PIN and then

press the ENTER button.

• Enter a temporary 4-digit PIN of your choice and

then press the ENTER button.

• The LED glows up for 2 sec. Then the keypad light

goes off. The radio code keypad is ready for

operation again.

• To use the radio code keypad with the latest

temporary PIN enter the 4-digit temporary PIN and

then press the ENTER button. You are allowed to

use this PIN three times and then it is automatically

cleared.

iverSender

P rstecker

Steckerbuchse

Cover

Keypad light

Socket

Programming plug

ctive

transmitter

Mounting holes

Screws

Lock

Coin

Wall bracket

all

lug

Marantec Command 231 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Marantec Command 231

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info