Bedienungsanleitung Marantec Command 231 (Seite 2 von 2) (Englisch)

742654

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Use of the radio code keypad

To protect the radio code keypad keep the cover

closed when it is not in use.

witch on the keypad light:

• Press the LIGHT button.

The keypad light is on for 5 sec.

pen and close the garage door:

• Enter the programmed 4-digit PIN and then press

the ENTER button. The garage door starts to

move.

• After having pressed the ENTER button, the radio

code keypad remains active for approx. 18 sec.

and the LED is on. During this period of time you

can stop the garage door by pressing any button

(except the LIGHT button).

• Under certain conditions it may be necessary to

keep one button pressed so that your garage door

control works. In this case enter the 4-digit PIN

and then hold the ENTER button. The garage door

moves as long as the ENTER button is held.

Advice:

In case a PIN longer than 4 digits is entered,

only the last 4 digits are considered as

valid. If three wrong PIN's are entered in

sequence, the radio code keypad cuts off to

prevent unauthorised access. After 2 min.

the radio code keypad is ready for use

again.

Light function (to switch other devices):

• To actuate another device (e.g. switch on the yard

light), press the LIGHT button and then the enter

button.

• To switch off the other device (e.g. the yard light),

press the LIGHT button again and then the ENTER

button.

Change the PIN

• Hold "button 0" for approx. 3 sec. until the LED

flashes quickly.

• Enter the PIN to be changed and then press the

ENTER button.

• Enter the new 4-digit PIN and then press the

ENTER button. The LED is on for 2 sec. (no

flashing).

• The radio code keypad is now ready for operation

with the new PIN (the old PIN is no longer valid).

Clear memory

• Press the LIGHT button.

-> After 3 sec. the LED starts to flash quickly.

• Hold the LIGHT button.

• While holding the button, enter PIN 9-9-9-9.

• Release the LIGHT button.

-> The memory is now cleared.

The LED is on for 2 sec.

Advice:

After clearing the memory the radio code

keypad is programmed with 1 random

code and PIN 1-2-3-4.

Replace batteries

• Take a coin to turn the lock on the bottom side of

the wall bracket anti-clockwise. Then take the

radio code keypad out of the wall bracket.

• Unscrew the back cover of the housing of the

radio code keypad.

• Take out the old batteries.

• Insert 2 new 3V batteries, CR 2032. Observe right

poling. Test the function of the unit (The radio

code keypad is designed that it will recognize all

previously programmed codes and PIN's after

change of battery).

• Screw again the back cover of the housing to the

radio code keypad.

dvice:

Don't dispose of old batteries in the

dustbin! Return them to your dealer or

dispose of in a recycling container for used

batteries.

Technical details

Frequency: 868,3 MHz (max. 0.36 mW)

433,92 MHz (max. 0.13 mW)

Voltage: 2 batteries 3V, CR 2032

Current input: approx. 11 mA

Size: 70 x 100 x 30 mm (B x H x T)

Weight: approx. 120 g

Protection category: IP 54

Range of temperature: -20°C to 60°C

Designated use

The radio code keypad is to be used to control door

operator and to switch on and off electrical devices

(power-operated units).

The Declaration of Conformity can be looked up at

the manufacturer mentioned in supply documents.

Simplified EU declaration of

conformity

Hereby, Marantec Antriebs- und Steuerungs technik

GmbH & Co. KG declares that the radio equipment

type Command 231 is in compliance with Directive

2014/53/EU. The full text of the EU declaration of

conformity is available at the following internet

address:

www.marantec.com

᪾

Version: 09.2017

#70794

1 - GB 360232 - M - 0.5 - 0404

Gehäuseunterschale

2Batterien3V,CR2032

2 batteries 3V, CR 2032

Back cover of housing

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marantec Command 231 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Marantec Command 231

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info