494327
5
Zoom out
Zoom in
Vorherige Seite
1/8
Nächste Seite
Marmitek X-10
Infrared interface type IRIX35
26
Technical characteristics
Transposes 38 kHz InfraRed (IR) signals from the remote
control device into Marmitek X-10 commands on the power
line.
Axial sensitivity: 25 mtr. range (edge 45°, 7 m. range).
Possibility for standard and "toggle" IR receipt.
Possibility to control one user definable letter code
(16 addresses).
Designed as an wall- or ceiling mountable unit or for
stand-alone use.
The infrared protocol is compatible with the existing
X10 IR-protocol. This means that all standard X10 compatible
IR remote transmitters (controls) can be used.
Application options
The IRIX35 can be used to receive infra red-commands (IR) from
Marmitek X-10 remote controls and send them over the power
line to switch or dim Marmitek X-10 actuators (see figure 1).
Marmitek X-10 Infrared interface type IRIX35
27
Figure 1.
Marmitek Home Control Box
If the IRIX35 is used in combination with the Marmitek Home
Control Box. The IRIX35 can be used to activate the previously
programmed macros in the Marmitek Home Control Box, using a
remote control device.
Marmitek X-10 modules
IRIX35
Infrared
signals
Remote control
Marmitek
Home Control
Box
Lighting
circuit
signal
28
In principle, the IRIX35 can be used in two ways:
1. Fitted to a distribution box.
2. Connected to a wall socket.
Note: Switch off the power before starting the
assembly!
Fitting to a distribution box
To fit the IRIX35 to a distribution box, follow the steps below.
Remove the cover of the IRIX35 by loosening the screw at
the top.
Feed live and neutral through the rear plate by making an
opening through the sticker covering the mounting plate.
Firmly screw the mounting plate with screws to the
distribution box.
Connect live and neutral to the connector of the
mounting plate.
Firmly tighten the cover of the IRIX35 to the mounting
plate again.
!
Assembly
29
A
Fitting to a distribution box.
30
Connecting the power cord for use in a wall socket
If you wish to connect the IRIX35 to a wall socket, you must
connect the power cord provided.
To connect the power cord to the IRIX35, follow the steps
below.
Remove the cover of the IRIX35 by loosening the screw
at the top.
Use a Stanley knife to carefully cut open the recess on the
narrow side of the mounting plate so that the power cord
can be fed through.
Fit live and neutral to the connector and feed the cable
through the cable channel in the mounting plate.
Firmly tighten the cover of the IRIX35 to the mounting
plate again.
Assembly
(cont'd.)
5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Marmitek IRIX35 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info