168923
6
Zoom out
Zoom in
Vorherige Seite
1/54
Nächste Seite
6
INSTALLATION
Notes:
Choose the mounting location where the unit
will not interfere with the normal driving function
of the driver.
Before finally installing the unit, connect the
wiring temporarily and make sure it is all
connected up properly and the unit and the
system work properly.
Use only the parts included with the unit to
ensure proper installation. The use of
unauthorized parts can cause malfunctions.
Consult with your nearest dealer if installation
requires the drilling of holes or other
modifications of the vehicle.
Install the unit where it does not get in the
driver’s way and cannot injure the passenger if
there is a sudden stop, like an emergency stop.
If installation angel exceeds 30°from horizontal,
the unit might not give its optimum
performance.
Avoid installing the unit where it would be
subject to high temperature, such as from direct
sunlight, or from hot air, from the heater, or
where it would be subject to dust, dirt or
excessive vibration.
DIN FRONT/REAR-MOUNT
This unit can be properly installed either from “Fr
ont”
(conventional DIN Front-mount) or “Rear” (DIN
Rear-mount installation, utilizing threaded screw
holes at the sides of the unit chassis). For detail
s,
refer to the following illustrated installation met
hods.
TAKE OUT SCREW BEFORE
INSTALLATION
Before install the unit, please remove the two
screws.
DIN FRONT-MOUNT (Method A)
Installation Opening
This unit can be installed in any dashboard having
an opening as shown below:
Installing the unit
Be sure you test all connections first, and then
follow these steps to install the unit.
1. Make sure the ignition is turned off, and then
disconnect the cable from the vehicle battery’s
negative (-) terminal.
2. Disconnect the wire harness and the antenna.
3. Press the release button on the front panel and
remove the control panel (see the steps of
“removing the front panel”).
4. Lift the top of the outer trim ring then pull it out to
remove it.
5. The two supplied keys release tabs inside the
unit’s sleeve so you can remove it. Insert the
keys as far as they will go (with the notches
facing up) into the appropriate slots at the
middle left and right sides of the unit. Then slide
the sleeve off the back of the unit.
30
Take out screw
before installation.
6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Marquant mcr 1283 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info