Bedienungsanleitung Midea Mission - 27 (Seite 6 von 8) (Englisch)

665692

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

99 1010

Refrigerant pipe connection

Oblique

Roughness

Burr

Main cause for refrigerant leakage is due to defect

in the flaring work. Carry out correct flaring work

using the following procedure:

A: Cut the pipes and the cable.

1. Use the piping kit accessory or pipes purchased locally.

2. Measure the distance between the indoor and the

outdoor unit.

3. Cut the pipes a little longer than the measured distance.

4. Cut the cable 1.5m longer than the pipe length.

1. Flaring work

Fig.11

Fig.12

Drain joint installation

Seal

Drain joint

Base pan hole of

outdoor unit

Seal

Drain pipe

(A)

(B)

For the drain joint with the seal(Fig.11 (A)), first

fit the seal onto the drain joint, then insert the

drain joint into the base pan hole of outdoor unit,

rotate 90 to securely assemble them. To install

drain joint as shown in Fig.11 (B), insert the drain

joint into the base pan hole of outdoor unit until it

remains fixed with a clicking sound. Connecting

the drain joint with an extension drain hose (Locally

purchased), in case of the water draining off the

outdoor unit during the heating mode.

NOTE: In cold areas, do not use a drain hose with

the outdoor unit.(otherwise, drain water may freeze)

NOTE: The drain joint is slightly different

according to the different outdoor unit.

Outdoor unit

dimension

mm(WxHxD)

A(mm)

458

B(mm)

250

487

298

504

560

335

340

549 276

Mounting dimensions

700x540x240

780x540x250

770x555x300

845x700x320

810x558x324

Anchor the outdoor unit with a bolt and nut 10 or

8 tightly and horizontally on a concrete or rigid mount.

Settlement of outdoor unit

NOTE: The outdoor unit you purchase may be like one

of the following. Install the outdoor unit according to the

dimension as indicated in the table below:

Air inlet

Air outlet

Air inlet

Fig.8

Install the outdoor unit on a rigid base to

prevent increasing noise level and vibration.

Determine the air outlet direction where the

discharged air is not blocked.

In the case that the installation place is exposed

to strong wind such as a seaside, make sure the

fan operating properly by putting the unit lengthwise

along the wall or using a dust or shield plates.

Specially in windy area, install the unit to prevent the

admission of wind. If need suspending installation,

the installation bracket should accord with technique

requirement in the installation bracket diagram.

The installation wall should be solid brick, concrete or

the same intensity construction, or actions to reinforce,

damping supporting should be taken. The connection

between bracket and wall, bracket and the air conditioner

should be firm, stable and reliable.

Be sure there is no obstacle which block radiating air.

Fig.9

OUTDOOR UNIT INSTALLATION

Outdoor installation precaution

1. Pass the piping through the hole in the wall.

2. Hook the indoor unit onto the upper portion

of installation plate(Engage the indoor unit with

the upper edge of the installation plate). Ensure

the hooks are properly seated on the installation

plate by moving it in left and right.

3. Piping can easily be made by lifting the indoor

unit with a cushioning material between the

indoor unit and the wall. Get it out after finish

piping. When use a wall embedded pipe, the

indoor unit can be moved to the left or right for

30~50mm(model dependent), which offers

sufficient space to arrange the pipes and ensure

the indoor unit fully close to the wall after installation.

4. Press the lower left and right side of the unit

against the installation plate until hooks

engages with the their slots.

Indoor unit installation

Strong

wind

Strong

wind

Barrier

Incorrect

Wall embedded pipe

Move to left or right

150mm

30~50mm

Correct

OUTDOOR UNIT INSTALLATION

Fig.10

NOTE: Connective pipe length will affect the

capacity and energy efficiency of the unit. The

nominal efficiency is tested basing on the pipe

length of 5 meters. Consult the technicians to

purchase proper size connective pipe for your

machine..

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Midea Mission - 27 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Midea Mission - 27

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info