Bedienungsanleitung MTD Zero Turn Serie RZT-S (Seite 15 von 18) (Englisch)

629100

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

English Operating Manual

Cleaning the cutting

mechanism

Danger

Injury hazard due to sharp cutting

blades

Wear protective gloves.

If the unit has more than one

cutting mechanism, moving one

cutting mechanism may cause the

other cutting mechanisms to move

as well. Caution when cleaning the

cutters.

Warning

Damage to engine

The mower must not be tilted to an

angle greater than 30°. This might

cause fuel to run into the com-

bustion chamber and could lead

to engine damage.

 Raise the cutting mechanism

fully.

 Clean the cutting compartment

with a scrubbing brush, hand

brush or cloth.

Cutters with cleaning nozzle

(optional)

Fig. 18

Place the appliance on an even

surface free of debris, stones, etc.,

and engage the locking brake.

1.Use a commercially available

quick-release coupling to attach

a water hose.

2.Start the engine.

3.Lower the cutters, and switch ON

for a few minutes.

4.Switch OFF the cutters and

engine.

5.Detach the water hose.

Repeat steps 1 to 5 for the second

cleaning nozzle (if provided).

At the end of cleaning (steps 1 to

5):

 Raise the cutters to the top,

 start the engine, and switch ON

the cutters for a few minutes to

dry them.

Maintenance

Follow the maintenance instruc-

tions in the engine handbook. At

the end of the season have the unit

inspected and serviced by a repair

shop.

Warning

Environmental hazard caused

by engine oil

Waste oil resulting from a routine

oil change should be taken to an

approved collection point or

specialist disposal company.

Batteries are an environmental

hazard

Do not throw used batteries into the

household refuse. Hand over used

batteries to your dealer or to

a waste management company.

Remove the battery before

scrapping the unit.

Using jump leads

Danger

Never bridge a defective or frozen

battery with jump leads.

Ensure that the units and the jump

lead clips do not touch each other

and that the ignitions are switched

off.

 Connect the red jump lead to the

positive terminal (+) of the flat

battery and the donor battery.

 Connect the black jump lead first

to the negative terminal (–) of the

donor battery. Connect the other

clip to the frame of the engine

block of the tractor with the flat

battery (as far away from the

battery as possible).

Note

If the donor battery is installed in

a vehicle, this vehicle must not be

started during the jump starting

process.

 Start the tractor with the flat

battery and actuate the parking

brake.

 Disconnect the jump leads in

reverse sequence.

Tyre pressure

Warning

Never exceed the maximum

permitted tyre pressure (see tyre

wall). When pumping up the tyres,

do not stand in front of or over the

tyre.

Excessive tyre pressure reduces

the service life of the tyres. Always

check the tyre pressure before

driving.

After 5 operating hours

 First engine oil change.

See engine manual for

subsequent intervals.

 Use the oil channel or (optional)

quick oil drain (Fig. 14).

After 10 operating hours

 Lubricate all rotating and bearing

points of the accelerator pedal

and brake pedal with several

drops of light oil.

 Clean battery poles and

terminals.

Every 25 operating hours

 Lubricate all blade shafts,

tensioning pulleys and

tensioning pulley holders via the

grease nipples using grease type

251H EP. Have this work carried

out by a service centre.

 Lubricate the wheel bearings and

front wheel axes with 251H EP

type grease applied to their

respective grease nipples.

 Remove grass and dirt around

the blade shafts beneath the

covers. Have this work carried

out by a service centre.

 Lubricate the steering with

grease Type 251H EP via the

grease nipples on the steering

support. Have this work carried

out by a service centre.

Every 50 operating hours

 Have dirt and grass remnants

removed from the drive gear

by a repair shop.

If required

Charge the battery

If you are not using the unit for

a prolonged period, it is recommen-

ded to take the battery out of the

unit and charge it before storage,

as well as every 2 months during

storage, and before starting up the

unit again.

Check the battery’s charged state

with a voltmeter. When the charged

state is less than 12.6 V (DC)

recharge the battery (max 12 V

at 6 A) with a battery charger in

accordance with the table.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

MTD Zero Turn Serie RZT-S Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von MTD Zero Turn Serie RZT-S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info