Bedienungsanleitung MTD Zero Turn Serie RZT-S (Seite 16 von 18) (Englisch)

629100

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

Operating Manual English

Note

Follow the instructions in the

operating manual for your battery

charger.

Replacing fuses

 Replace defective fuses only with

ones of an equal strength.

Once per season

 Lubricate all rotating and bearing

points (operating lever, height

adjustment of the cutter deck ...)

with several drops of light oil.

 Clean the spark plug and check

the gap between the electrodes

or replace the plug. See engine

handbook.

 The rear axles must be lubricated

with a special-purpose (water-

repellent) grease at a specialised

garage.

 Have the cutting blade

sharpened or replaced in

a specialist workshop.

Note

Regularly check (when visiting your

workshop) the condition of the

mower deck V-belt.

Removing/Installing and

adjusting cutter deck

Danger

Injury hazard if engine is started

inadvertently

Protect yourself against injury.

Before carrying out any work on the

mower

– park the appliance on a level

surface,

– switch off the engine,

– withdraw the ignition key,

– switch off PTO,

– lock the parking brake.

– wait until all moving parts have

come to rest and the engine has

fully cooled,

– remove the spark plug connector

on the engine in order to prevent

the engine from accidentally

being started.

Danger

Injury hazard due to sharp cutting

blade.

Wear protective gloves.

Disassembly

 Raise cutter deck into a position

in which the V-belt is as

horizontal as possible between

the cutter deck and PTO clutch.

 Remove the V belt (1) from the

PTO clutch/motor pulley (2) –

fig. 20.

To do this, pull left or right side of

the V-belt backwards and then

downwards while manually

turning the engine belt pulley in

the opposite direction.

Note:

Work carefully to avoid

trapping your fingers.

 Move cutting height adjustment

lever to the lowest position.

 Remove front fixing bracket from

the cutter deck – Fig. 19. Pull

cotter pin (1) and pull the fixing

bracket (2) out of the holder.

Note:

In doing so, support the

cutters firmly so that they cannot

simply drop to the ground.

 Pull out the pin (1) on the left and

right of the cutter deck to

disconnect the cutter deck from

the hanger (2) – Fig. 13.

Note:

In doing so, support the

cutters firmly so that they cannot

simply drop to the ground.

 Move cutting height adjustment

lever to the highest position.

 Pull out the cutters from beneath

the appliance.

Assembly

To reinstall the cutters perform the

above steps (for removing the

cutters) in reverse order. Work

proceeds faster when you are

assisted by a second person. Make

sure that the suspension units are

in their respective recesses on the

cutter mount and the pin has

engaged correctly.

Note

Following assembly, check that the

V-belt is positioned correctly and is

not twisted – Figs. 21 to 23.

Setting the cutter level

When mowing does not appear to

be parallel to the lawn the cutters

can be aligned.

Note

Before aligning the cutters check

the tyre pressure on the appliance.

Setting the side level

Fig. 11

 Raise the cutters to the top.

 Carefully turn the outer cutters

(risk of injury) transverse to the

drive direction.

 Measure the distance between

the ground and the ends of the

two outer cutters. The result

should be the same. If required,

set the correct level by rotating

the setting segment (2) on the left

cutter deck side. To do so first

loosen (but do not remove) the

cap bolt (1) and retighten this

after the adjustment.

Set the level from front to back.

Fig. 10

Note

Set/check the side level before this

adjustment.

 Raise the cutters to the top.

 Carefully turn the outer cutters

(risk of injury) parallel to the drive

direction.

 Measure the distance between

the ground and the end of the

right cutter. The end of the front

cutter should be about 3.2–6 mm

lower than the end of the rear

cutter. You may have to adjust

the front receiver (1). To do this,

set the correct level by adjusting

the nut (2).

Voltmeter Battery

charging

state

Charging

time

12.7 volts 100 % –

12.4 volts 75 % approx.

90 min.

12.2 volts 50 % approx.

180 min.

12.0 volts 25 % approx.

280 min.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

MTD Zero Turn Serie RZT-S Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von MTD Zero Turn Serie RZT-S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info