Bedienungsanleitung Multiplex Power Peak D7 EQ-BID - 30 8129 (Seite 23 von 92) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

628910

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

Operating Instructions

Power Peak

D7 EQ-BID

Order No.

8129

7. MEMORY NAME MENU

Any of the twenty available memory places can be selected in

the "MEMORY NAME" display. In this menu it is also possible to

program all the parameters for the active memory.

Use the "+" and "-" buttons to select the line you wish to program.

Once you have marked the appropriate line with the arrow, you

have to activate the parameter by pressing the "START / ENT."

button (dark background). The value to be changed can then be

altered using the "+" and "-" buttons. When the value has been

changed, press the "START / ENT." button to save the value.

When the line for entering the battery type is active, you can use

the "+" and "-" buttons to select one of the following battery types:

Nickel-Cadmium bat-

tery (NiCd), Nickel-

Metal-Hydride batte-

ry (NiMH), Lithium-

Polymer battery

(LiPo), Lead-Acid

battery (Pb), Lithium-

Ferrophosphate bat-

tery (LiFe), Lithium-

Ion battery (LiIo).

Pressing the

"START / ENT." but-

ton again activates

the line for entering

the number of cells.

Use the "+" and "-"

buttons to set the

battery voltage / cell count.

In the line for entering the capacity you can press the "+" and "-"

buttonstoadjustthebatterycapacityin100mAhincrements.

•NC / NiMH max. 60 Ah

•Lithium max. 60 Ah

•Lead-acid/Pb max. 60 Ah

When the "Charge current" line is active, the charge current can

be defined within the range 0.1 A to 20 A in 100 mA increments.

Be sure to observe the battery manufacturer's specification.

In the "Discharge current" line the discharge current can be

entered in the same way, within the range 0.1 A to 10 A, again in

increments of 100 mA.

The final discharge voltage (Discharge volt.) per cell can be

adjustedbypressingthe"+"and"-"buttonsinincrementsof0.1

V,accordingtothebatterytype.

•Nickel-Cadmiumbattery(NiCd): 0.1-1.1V/cell

•Nickel-Metal-Hydridebattery(NiMH): 0.1-1.1V/cell

•Lithium-Polymerbattery(LiPo): 3.0-3.3V/cell

•Lithium-Ferrophosphatebattery(LiFe): 2.6-2.9V/cell

•Lithium-Ionbattery(LiIo): 2.9-3.2V/cell

•Lead-Acidbattery(Pb): 1.8-2.0V/cell

Factory settings are guide values only.

Thefunction"TVCvoltage"(TerminalVoltageControl)isusedto

alter the final charge voltage for Lithium batteries. The value is

entered as a voltage per cell.

Theadjustmentrangeextendsfrom3.58-4.25Volt/cell,depen-

ding on battery type. This value is stored permanently in the

"Memory name" menu. If a BID chip or key is connected, these data

are only stored temporarily.

Important note:

SettingthecorrectvalueforTVCvoltageistheresponsibilityofthe

user, and is excluded from the guarantee.

Ifthe"TRICKLE CURRENT"lineis activated, youcan adjust the

trickle charge current for NiCd and NiMH batteries in increments

of 1 mA. For these battery types the range lies between OFF and

50 - 300 mA.

The Delta-Peak cut-off sensitivity (Peak sens.) can be set for NiCd

and NiMH batteries.

•Nickel-Cadmiumbattery(NiCd): 3-15mV/cell

•Nickel-Metal-Hydridebattery(NiMH): 3-15mV/cell

The table on the next page shows an overview of all the parameters

andadjustmentrangesfortheindividualbatterytypes.

(01) Memory name. .

LiPo7.4V2000mAh

Chg Current : 2.0 A

dChg Current : 1.0 A

dChgVolt  :3.2V/C

TVCVolt  :4.20V

(01) Memory name . . .

NiMH 6 cells 2000 mAh

Chg Current : 2.0 A

dChg Current : 1.0 A

dChgVolt :1.0V/C

Trickle : 100 mA

DeltaPeak : 4mV/C

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Multiplex Power Peak D7 EQ-BID - 30 8129 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info