Bedienungsanleitung Mustek PowerMust 636 (Seite 2 von 28) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Finnisch)

677942

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

8 hours

CAUTION: NEVER connect a laser printer or scanner to the UPS unit. This may cause the

damage of the unit.

4. Installation and Initial Startup

NOTE: Before installation, please inspect the unit. Be sure that nothing inside

the package is damaged.

Placement & Storage Conditions

Install the UPS in a protected area that is free of excessive dust and has adequate air flow.

Please place the UPS away from other units at least 20 cm to avoid interference. Do NOT

operate the UPS where the temperature and humidity is outside the specific limits.

(Please check the specs for the limitations.)

Connect to Utility and Charging

Before initial use, please plug in the AC input cord to the wall

outlet and turn on the UPS for charging. For the best results,

suggest to charge the battery at least 8 hours before initial use.

Connect the Loads

Plug in the loads to output receptacles on the rear panel of the

UPS. Simply turn on the power switch of UPS unit, then devices

connected to the UPS will be protected by UPS unit.

Turn On/Off the Unit

Turn on the UPS unit by pressing the power switch. Turn off the UPS unit by pressing

again the power switch.

Indicators & Alarm Table for Operation

Conditions Visual Indicator Alarm

AC Mode Green LED lighting Off

Battery Mode Green LED flashing every 10

seconds

Sounding every 10

seconds

Low battery at battery

mode

Green LED flashing every second

and Red LED lighting

Sounding every second

Fault Red LED lighting Continuously sounding

Alarm for

over-temperature

protection

Red LED flashing every 0.5

seconds

Off

5. Important Safety Warning (SAVE THESE INSTRUCTIONS)

CAUTION! To prevent the risk of fire or electric shock, install in a temperature and

humidity controlled indoor area free of conductive contaminants. (See the specifications for

the acceptable temperature and humidity range.)

CAUTION! To reduce the risk of overheating the UPS, do not cover the UPS' cooling vents

and avoid exposing the unit to direct sunlight or installing the unit near heat emitting

appliances such as space heaters or furnaces.

CAUTION! Do not attach non-computer-related items, such as medical equipment,

life-support equipment, microwave ovens, or vacuum cleaners to UPS.

CAUTION! Do not plug the UPS input into its own output.

CAUTION! Do not allow liquids or any foreign object to enter the UPS. Do not place

beverages or any other liquid-containing vessels on or near the unit.

CAUTION! In the event of an emergency, press the OFF button and disconnect the power

cord from the AC power supply to properly disable the UPS.

CAUTION! Do not attach a power strip or surge suppressor to the UPS.

CAUTION! If the UPS is with metal chassis, for safety purpose, grounding is a must during

UPS installation in order to reduce leakage current below 3.5A.

Attention hazardous through electric shock. Also with disconnection of this unit from the

mains, hazardous voltage still may be accessible through supply from battery. The battery

supply should be therefore disconnected in the plus and minus pole at the quick connectors

of the battery when maintenance or service work inside the UPS is necessary.

CAUTION! Servicing of batteries should be performed or supervised by personnel

knowledgeable of batteries and the required precautions. Keep unauthorized personnel

away from batteries.

CAUTION! When replacing the batteries, use the same number and type of batteries.

CAUTION! Internal battery voltage is 12VDC. Sealed, lead-acid, 6-cell battery.

CAUTION! Do not dispose of batteries in a fire. The battery may explode. Do not open or

mutilate the battery or batteries. Released electrolyte is harmful to the skin and eyes.

CAUTION! Unplug the UPS prior to cleaning and do not use liquid or spray detergent.

CAUTION! A battery can present a risk of electric shock and high short circuit current. The

following precaution should be observed before replacing batteries:

1) Remove watches, rings, or other metal objects.

2) Use tools with insulated handles.

3) Wear rubber gloves and boots.

4) Do not lay tools or metal parts on top of batteries.

5) Disconnect charging source prior to connecting or disconnecting batteries terminal.

EN EN

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mustek PowerMust 636 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info