Bedienungsanleitung NAD C 326 BEE (Seite 6 von 16) (Englisch)

493507

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

IDENTIFICATION OF CONTROLS

FRONT PANEL

1 STANDBY: With the rear panel POWER switch set to ON position,

press this button to switch ON the C 326BEE from standby mode.

The Standby LED indicator will turn from amber to blue. Pressing the

STANDBY button again turns the unit back to standby mode.

The C 326BEE can also be switched ON from standby mode by pressing

any of the front panel buttons.

AUTO STANDBY

Auto Standby feature is an integral feature of the C 326BEE that

conforms to European ecodesign regulations. When Auto Standby is

enabled, the C 326BEE will automatically go to standby mode if there is

no active input at current source or no user interface interaction within

30 minutes.

Auto Standby can be enabled or disabled by the following button

combinations and Standby LED indicator response. Execute below

steps while the C 326BEE is at operating mode.

Press and hold [AUX] button and then press Standby button. Observe

the number of times the Standby LED ashes.

• Auto Standby enabled : Standby LED ashes once.

• Auto Standby disabled : Standby LED ashes twice.

2 STANDBY LED: This indicator will light up amber when the C 326BEE

is in standby state. When the C 326BEE is at ON state, this indicator will

illuminate blue. When infrared command from the SR 8 is received, this

indicator will also ash momentarily.

In cases of serious abuse of the C 326BEE, such as excessively low

loudspeaker impedance and short circuit, the C 326BEE will engage its

Protection circuitry, indicated by the Standby LED turning from blue to

red and the sound being muted.

In such a case, turn the C 326BEE OFF by the rear panel POWER

switch, wait for it to cool down and/or check the speaker connections,

making sure the overall loudspeaker impedance doesn’t go below 4

ohms. Once the cause for the protection circuitry to engage has been

removed, switch ON the rear POWER switch and the STANDBY button to

resume normal operation.

3 SOFT CLIPPING INDICATOR: The blue SOFT CLIPPING LED shows

that the SOFT CLIPPING mode is engaged. Refer also to the item below

about SOFT CLIPPING at the IDENTIFICATION OF CONTROLS – REAR

PANEL.

4 REMOTE SENSOR: Point the SR 8 remote control at the remote

sensor and press the buttons. Do not expose the remote sensor of the

C 326BEE to a strong light source such as direct sunlight or illumination.

If you do so, you may not be able to operate the C 326BEE with the

remote control.

Distance: About 23ft (7m) from the front of the remote sensor.

Angle: About 30o in each direction of the front of the remote sensor.

5 PHONES: A 1/4” stereo jack socket is supplied for headphone listening

and will work with conventional headphones of any impedance.

Inserting a headphone jack into this socket automatically switches o

the loudspeakers. The volume, tone and balance controls are operative

for headphone listening. Use a suitable adapter to connect headphones

with other types of sockets, such as 3.5mm “personal stereo” jack plugs.

NOTE

Make certain that the volume control is turned to minimum (fully

counter-clockwise) before connecting or disconnecting headphones.

Listening at high levels can damage your hearing.

6 MP SOCKET: Using a 3.5mm stereo plug, connect into this socket the

audio output of a Media Player.

NOTES

• If an external Media Player is connected to the front MP socket (using a

3.5mm stereo plug) while listening to a MP line-level source, the external

Media Player will be directly selected with the MP line-level source

immediately disconnected.

• It is recommended to mute the volume or switch to a dierent input

before plugging/unplugging the external Media Player cable.

111095 6 7 8

2 3 4

ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD C 326 BEE Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD C 326 BEE

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info